User Account

All Pages

A harmonic motion is expressed as xt 06cos18pit - pi6

Assignment Help Mechanical Engineering
Reference no: EM13623229

A Harmonic motion is expressed as x(t) = 0.6cos(18pi*t - pi/6), where x(t) is measured in inches, t in seconds and the phase angle in radians. Determine:

a) the frequency in rad/s and in Hz.

b) the period of motion.

c) the amplitude of maximum displacement, velocity and acceleration.

Reference no: EM13623229

Questions Cloud

Producers of pvc pipes want to have a supply of pipes : producers of pvc pipes want to have a supply of pipes sufficient to meet marketing needs. they wish to survey
You recently purchased a stock that is expected to earn 29 : you recently purchased a stock that is expected to earn 29 percent in a booming economy 18 percent in a normal economy
If the block compresses the spring 48 cm before coming to : a block of 2.7 kg slides was moving with a speed of 1.0 ms on a frictionless horizontal surface until it encounters a
Cholesterol values are obtained in a group of people before : cholesterol values are obtained in a group of people before and after being given a drug. we want to test whether the
A harmonic motion is expressed as xt 06cos18pit - pi6 : a harmonic motion is expressed as xt 0.6cos18pit - pi6 where xt is measured in inches t in seconds and the phase angle
A commerical real estate property has been evaluated by an : a commerical real estate property has been evaluated by an appraiser who estimates the following net operating income
Producers of pvc pipes want to have a supply of pipes : producers of pvc pipes want to have a supply of pipes sufficient to meet marketing needs. they wish to survey
What is the sampling distribution of a sampe mean for a : i what is the sampling distribution of a sampe mean for a normally distributed random variable.ii if a variable iq is
If the cycle operates on a stationary mass of 1 kg of water : in a carnot cycle heat is supplied at 350degc and rejected at 27degc. the working fluid is water which while receiving

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The experiment is repeated with a metallic sphere of the

a small sphere of reference-grade iron with a specific heat of 447 jkgk and a mass of 0.515 kg is suddenly immersed in

  Determine a the maximum temperatureand pressure that occur

an ideal otto cycle has a compression ratio of 8. at the beginning of the compression process air is at 100kpa and

  Argon gas enters an adiabatic compressor under steady flow

argon gas enters an adiabatic compressor under steady flow conditions at 12o kpa and 30 c with a velocity of 20 ms and

  Determine the magnitude t of applied torque

the tank has a 180mm diameter and 12 mm wall thickness. knowing that the tank contains compressed air under a pressure of 8 Mpa, determine the magnitude t of applied torque for which the maximum normal stress in tank is 75 Mpa.

  The duration of the impact is 0002 seconds determine the

a 2-kg sphere a is moving toward the right at 4 ms when it strikes the end of a 5 kg slender bar b. the coefficient of

  Piston and flywheelconsider the one-cylinder four-stroke

piston and flywheelconsider the one-cylinder four-stroke engine assembly shown in figure 1. the mass of the piston p is

  Two kg of a mixture having an analyis of on a mass basis of

two kg of a mixture having an analyis of on a mass basis of 30 nitrogen 40 carbon dioxide 30 oxygen is compressed

  Neglecting changes in kinetic and potential engery and

a heat exchanger at an industrial plant uses river water to condense 2x105 kgh of steam from saturated vapor to

  Determine the angular accelerations of gears b and c

determine a) the angular accelerations of gears B and C, b) the accelerations of the points on gears B and C which are in contact when t = 0.5 s.

  Find a cylindrical container that is large enough that it

find a cylindrical container that is large enough that it takes at least one minute to drain you may have to create an

  Calculate the final temperature in the small cylinder

If the filling is done rapidly, calculate the final temperature in the small cylinder, (a) assume that oxygen is an ideal gas with Cv= 5R/2 and (b) using accurate thermodynamic data for oxygen.

  What is the largets size mm internal through crack that a

1 the critical crack length for a through crack in a thick plate of 7150-t651 aluminum alloy that is in uniaxial

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd