A cylindrical wheel billet 1ft in diameter and 3ft long

Assignment Help Mechanical Engineering
Reference no: EM13345683

A cylindrical wheel billet 1ft. in diameter and 3ft. long, initially at 1000 F, is quenched in oil. Assume that the surface of the billet is 200 F throughout the quenched; assume that the convective heat transfer coefficient between the oil and the billet surface is very large. The steal has the following properties, which may be assumed independent of temperature: K = 25 Btu/h-ft-F, Cp = 0.11 Btu/lbm-F, p = 490 lbm/ft^3, a(alfa) = 130*10^-6 ft^2/s. Estimate the temperature of the hottest point in the billet after five minutes of quenching. Neglect end effects; make the calculation for a cylinder of the given diameter but of infinite length. 

Reference no: EM13345683

Questions Cloud

I a sample containing 203 ml of nitroglycerine density : 4 c3h5o9n3l rarr 12 co2g 6 n2g o2g 10 h2oga if a sample containing 2.03 ml of nitroglycerine density 1.592 gml is
Whats a good hypothesis for the reactivity of halide ions : whats a good hypothesis for the reactivity of halide ions lab in
You have a 1040-g mixture of table sugar c 12 h 22 o 11 and : you have a 10.40-g mixture of table sugar c 12 h 22 o 11 and table salt nacl. when this mixture is dissolved in 150. g
Is it better to have several small wires conducting : is it better to have several small wires conducting electricity or one big wire of the same cross section or better
A cylindrical wheel billet 1ft in diameter and 3ft long : a cylindrical wheel billet 1ft. in diameter and 3ft. long initially at 1000 f is quenched in oil. assume that the
10ml of 01m hno2 nitrous acid ka40x10-4is titrated with a : 10ml of 0.1m hno2 nitrous acid ka4.0x10-4is titrated with a .01m koh solution. after 10ml of the koh solution is added
What is the concentration of dissolved o2 in blood or : what is the concentration of dissolved o2 in blood or water at this partial pressure and a normal body temperature of
Make this molecule from any starting materials that are : kinoprene is an insect hormone. derivatives of this type of compound have the potential of being highly selective and
Reference the textbook problem 48 the rtd of problem 47 : reference the textbook problem 4.8. the rtd of problem 4.7 is used in the bridge circuit of figure 4.4. if r1 r2 r3

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What steel specification suitable for structural application

Find the stress in both members shown below and what steel specifications (types of steel) are suitable for structural applications?

  Estimate the torque required at the base of a flag pole

Estimate the torque required at the base of a flag pole to hold it in place in a 30mph wind. Assume the flag pole is a vertical cylinder with D=10cm and L=10m, and assume the wind drag force is uniform along the pole.

  A preheater involves the use of condensing steam at 100c on

a preheater involves the use of condensing steam at 100c on the inside ofnbspa bank of tubes to heat air that enters at

  An airplane flies horizontally at 550 ms its

an airplane flies horizontally at 55.0 ms. its propellernbspdelivers 1500 n of thrust forward force to overcome

  Applied loads and young''s modulus and poisson''s ratio

Applied Loads, Young's modulus, Poisson's ratio, The Young's modulus and the Poisson's ratio for copper are 124.8 GPa and 0.36 respectively. When a tensile load is applie to a 1.5cm diameter copper rod

  Derive the linearised equation about the operation

For the pendulum shown in the figure,the restoring torque due to gravity is given by T=mgLsin(thita). Derive the linearised equation about the operation point thita=0.

  What is the peak deflection of the diving board

Find the differential equation governing the motion of the diver while she is in contact with the board. Neglect any rotational inertia and what is the peak de?ection of the diving board?

  Is the displacement field compatible

A body with a plane stress field has material properties E, ν and has the following displacement field

  Why is the carnot cycle not suitable as an ideal cycle

why is the carnot cycle not suitable as an ideal cycle for all the power producing devices ?

  A venturi meter is inserted in a pipe whose diameter is 12

a venturi meter is inserted in a pipe whose diameter is 12 in. the diameter of the meter at its throat is 6 in. and the

  Determine the angle between his velocity vector and the line

Determine the angle between his velocity vector and the line from his position to the airlock's position.

  Determine the reaction force exerted by the nozzle

a curved nozzle assembly that discharges to the atmosphere is shown. The nozzle mass is 4.5 kg and its internal volume is 0.002 m^3. The fluid is water. determine the reaction force exerted by the nozzle on the coupling to the inlet pipe.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd