User Account

All Pages

A cylindrical tank is to contain gas at a pressure of 400

Assignment Help Mechanical Engineering
Reference no: EM13628128

A Cylindrical tank is to contain gas at a pressure of 400 psi, and for safety reasons, the hoop stress in the tank wall must not exceed 12,800 psi. If the tank is 6 feet long, and has an inside diameter of 2 feet, what minimum wall thickness should be specified?

Reference no: EM13628128

Questions Cloud

At the beginning of the compression process of an : at the beginning of the compression process of an air-standard otto cycle p1 14.7 lbin2 and t1 530degr. the maximum
Two coils are wound around the same cylindrical form when : two coils are wound around the same cylindrical form when the current in the first coils is decreasing at a rate of
Associated supplies are expected to cost 10000 per year the : a consulting firm is contemplating the purchase of a btu meter to measure the cooling loads on chillers at a purchase
A gaseous mixture consists of 75 methane and 25 ethane by : a gaseous mixture consists of 75 methane and 25 ethane by mass. one million cubic feet of this mixture is trapped in
A cylindrical tank is to contain gas at a pressure of 400 : a cylindrical tank is to contain gas at a pressure of 400 psi and for safety reasons the hoop stress in the tank wall
How to derive the expression for the magnitude of the : how to derive the expression for the magnitude of the plasma frequency for the case of an actual plasma that is overall
What force would be required to start a 250lb crate : what force would be required to start a 250lb crate sliding across a cement floor which has a coefficient of static
A well-insulated control volume operates at a steady state : a well-insulated control volume operates at a steady state and has one inlet location 1 and two outlets locations 2 and
Simutaneously the coolant carries the heat away from the : a shell and tube heat exchanger consists of a tubecarrying a fluid to be heated or cooled surrounded by another fluid

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  At the end of 4 years another b may be purchased with the

a firm is considering two alternatives that have no slavage value.alternative ainitial cost- 10700uniform annual

  Find the height of center of mass

find the best fit Gaussian Curve through the data and plot the data and curve on the same graph.

  Estimate the minimum collector area that would be required

it is proposed that solar energy be used to warm a large collector plate. this energy would in turn be transferred as

  Determine the amount of co2 emission per year that is saved

in usa 53 of total electric power is currently generated by coal-fired power plants. typically generation of 1 kwh of

  What is the velocity of the airplane

A Pitot tube measures the total pressure on an airplane flying at sea level as 1.07 x 10^5 N/m^2. What is the velocity of the airplane?

  Aconstant upward acceleration of 0372 fts2 determine the

cylinder b has a velocity of 1.517 fts downward at t0 and a constant upward acceleration of 0.372 fts2. determine the

  Saturated liquid refrigerant r-134a at 1159 bar enters an

saturated liquid refrigerant r-134a at 11.59 bar enters an adiabatic throttling valve which drops the pressure to 4.00

  Determine the pressure, temperature and enthalpy at entrance

A heat pump uses refrigerant-134a as the working fluid in an ideal vapour-compression refrigeration cycle between 0.14 and 0.8 MPa. The refrigerant leaves the compressor at a temperature of 40° C. Determine the pressure, temperature and enthalpy a..

  Assume frictionless flow through all piping and heat

a walk-in cooler using a vapor compression refrigeration cycle is configured as shown below. the cycle uses cfc22 or

  Specify a suitable temperature and wall thickness to give

one design calls for a diffusion flux of 5 108 molm2.s a tube radius of 0.125 m and inside and outside pressures of

  Gear c has a constant angular velocity of 1 rpm determine a

a simplified gear system for a mechanical watch is shown. knowing that gear a has a constant angular velocity of 1

  Determine the following 1 the compressor work kjkg 2 the

an ideal cold air-standard brayton cycle engine operates with air entering the compressor at 27 c. the pressure ratio

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd