A computer program to represent seig in its transient state

Assignment Help Mechanical Engineering
Reference no: EM131315379

1. Using MATLAB/Simulink®, write a computer program to represent the SEIG in its transient state.

2. Explain why an IG cannot self-excite under the following conditions:

(1) no residual magnetism,

(2) after too much inductive load, and

(3) after overcurrent.

What you have to do in order to allow the IG to self-excite again?

Reference no: EM131315379

Questions Cloud

Define the identified critical step of research in your word : Identify the most important step in the student's guide to research that you would need in order to analyze bullying.Define the identified critical step of research in your words.
Explain difference between rotor speed and rotor frequency : Explain the difference between rotor speed and rotor frequency. For s = -0.01 and a rotor speed of 1740 rpm, what is the rotor frequency for a 60 Hz induction generator?
Global employee and labor relations problems : Discuss three global employee and labor relations problems. How can organizations overcome these problems? Explain.
Identify the three categories of executive perks : Identify the three categories of executive perks. Provide specific examples for each category.
A computer program to represent seig in its transient state : Using MATLAB/Simulink®, write a computer program to represent the SEIG in its transient state.- What you have to do in order to allow the IG to self-excite again?
Identify the three categories of executive perks : Identify the three categories of executive perks. Provide specific examples for each category.
Analyze extent to which this emergency might affect quality : Analyze the extent to which this emergency might affect the quality of care provided to the patients and the unimpeded operation of the organization.
Prepare an introduction presenting an overview of the crime : The course materials present a number of criminological, sociological, and developmental theories that endeavor to explain delinquent behavior among juveniles. In this assignment, you will select a real-life, notorious crime committed by a juvenil..
Practical methods of generating residual magnetism : Discuss the four best-known practical methods of generating residual magnetism.- Discuss the advantages of a matrix partition to represent the transient state of an aggregation of SEIGs.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Negligible kinetic and potential energy effects

A counterflow heat exchanger operates at steady  state with negligible kinetic and potential energy effects. In one stream, liquid water enters at 108C and exits at 208C with a negligible change in pressure.

  Determine the irreversibility rate of the condenser

Determine the irreversibility rate of the condenser and the condenser's entrance and exit specific flow availabilities.

  Calculate the pressure temperature velocity and mass flow

air enters a converging-diverging nozzle of a supersonic wind tunnel at 1 mpa and 37 ordmc with a low velocity. the

  Application of a thermal barrier coating

The performance of gas turbine engines may be improved by increasing the tolerance of the turbine blades to hot gases emerging from the combustor. One approach to achieving high operating temperatures involves application of a thermal barrier coat..

  Determine the solar load fraction for a range of collector

Explain how the f-chart (Figure 7.32) can be used graphically to determine the solar load fraction for a range of collector sizes once the solar and loss parameters have been evaluated for only one system size. Hint: Consider a straight line passi..

  Determine the reactions on the beam at its support a

Determine the reactions on the beam at its support A in terms of the compression CA, shear VA, and bending moment MA.

  Find the contact force between the beams at b

The two cantilever beams have the same flexural rigidity EI. When unloaded, the beams just make contact at B. Find the contact force between the beams at B when the uniformly distributed load is applied.

  Design a small four-stroke cycle diesel engine

Give the design speed, displacement, number of cylinders, bore, stroke, bmep, and torque. All parameter values should be within typical, reasonable values and should be consistent with the other values. State all assumptions you make.

  The cyclic device rejects thermal energy to 40 c

a cyclic device operating as a refrigerator is being used to cool two refrigerated spaces. the first space is being

  How much would it cost to deliver one kilo watt-hour

How much would it cost to deliver one kilo Watt-hour? How does this compare with the cost of energy from your local electric utility at $0.10 per kilo Watt-hour?

  Determine the following quantities for the cylindrical part

A pressurized steel tank is constructed with a helical weld that makes an angle α = 55° with the longitudinal axis (see figure). The tank has radius r = 0.6 m, wall thickness t = 18 mm, and internal pressure p = 2.8 MPa. Also, the steel has modulu..

  Determine the largest allowable value of t

The 3-in.-diameter rod carries the 4000-lb · ft bending moment and a torque T. The yield stress of the material is 60 ksi. Determine the largest allowable value of T using the maximum distortion energy theory and a factor of safety of 2.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd