A composite is made up of 40 of filaments 100 mm in

Assignment Help Mechanical Engineering
Reference no: EM13632314

a) Most fiber-reinforced composites consist of three "parts": the fibers, the matrix, and the interfaces. Describe the major functions of each of these "parts".

b) Explain why a strong interface is a detriment to the properties of ceramic-matrix composites.

c) A composite is made up of 40% of filaments 100 mm in diameter of strength 3 GPa in a matrix of strength 80 MPa. The interfacial bond strength is 60 MPa. Determine the composite breaking strength if the filaments have average lengths of (a) 100 mm and (b) 2 mm.

Reference no: EM13632314

Questions Cloud

Hurricane katrina forced insurance companies to examine : hurricane katrina forced insurance companies to examine policy rates and originally determined that the average claim
Assuming an axial velocity at the eye of the impeller an : a helicopter gas turbine requires an overall compressor p.r. of 101. this is to be obtained using a two-spool layout
George said that sam would need to determine whether his : sam wanted to test a claim about the mean of a population whose standard deviation was unknown. he picked a simple
In the u s about 15 of the population is 65 years or older : in the u. s. about 15 of the population is 65 years or older senior citizens. it is estimated that 90 of seniors get a
A composite is made up of 40 of filaments 100 mm in : a most fiber-reinforced composites consist of three parts the fibers the matrix and the interfaces. describe the major
According to the national institute on alcohol abuse and : according to the national institute on alcohol abuse and alcoholism niaaa and the national institutes of health nih 41
A steam power plant operates with a boiler output of 20 kgs : a steam power plant operates with a boiler output of 20 kgs steam at 2 mpa 600degc. the condenser operates at 50degc
What are the temperature on the left edge of the wall the : a one dimensional wall of material kw10wmk is 50 mm thick with uniform heat generation qlsquolsquolsquo5106wm3. the
A rankine cycle operating with ammonia is heated by some : a rankine cycle operating with ammonia is heated by some low temperature source so the highest t is 120oc at a pressure

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A load of 500 pounds is placed on a cylinder of 1040

a load of 500 pounds is placed on a cylinder of 1040 carbon steel with a 2 inch radius. calculate the stress in

  Determine the headwater depth of a 1000 mm high by 1500mm

determine the headwater depth of a 1000 mm high by 1500mm wide concrete box culvert operating under outlet control

  Milk enters the tank through a 005 m diameter pipe at a

a large storage tank contains 500000 l of milk. milk enters the tank through a 0.05 m diameter pipe at a velocity of 3

  If money is worth 6 compounded annually to you then you

if money is worth 6 compounded annually to you then you should prefer to receive 1750 per year for 5 years than to

  If a torque of m2001-e-02tnm where t is in seconds is

gears a and b have a mass of 50kg and 15kg respectivly. their radii of gyration about their respective centers of mass

  The enthalpy of combustion for propane is -2044 kjmol how

the enthalpy of combustion for propane is -2044 kjmol. how many liters of propane at stp must be burned in order to

  A 0400 kg ball has a volume 148 x 10-4 m3 when dropped into

a 0.400 kg ball has a volume 1.48 x 10-4 m3. when dropped into water after a short time the sphere is observed to

  A tennis racket hits a tennis ball with a force of fat-bt2

a tennis racket hits a tennis ball with a force of fat-bt2 where a1 1280 nms b1 460 nms2 and t is the time in

  Atypical bacterial motor turning at a constant angular

some bacteria are propelled by biological motors that spin hair-like flagella. a typical bacterial motor turning at a

  Determine a the net power developed in mw b the rate of

air enters the compressor of an air-standard brayton cycle with a volumetric flow rate of 60 m3s at 0.8 bar 280 k. the

  Determine the new perigee and apogee altitudes of the

a satellite is in a circular orbit 250 mi above the surface of the earth. determine the new perigee and apogee

  At a surface cutting speed of 190 mmin the productive tool

at a surface cutting speed of 190 mmin the productive tool life was 60 minutes. at a surface cutting speed of 225 mmin

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd