A closed rigid tank whose volume is 15 m3 contains

Assignment Help Mechanical Engineering
Reference no: EM13344466

A closed, rigid tank whose volume is 1.5 m3 contains refrigerant 134a, initially a two phase lipuid-vapor mixture at 10C. the refrigerant is heated to a final state where temperature is 50C and quality is 100%. locate the initial and final states on a sketch of the T-v digram. determine the mass of vapor present at the initial and final state, each in kg. 

Reference no: EM13344466

Questions Cloud

A vehicle is stuck on the railroad tracks as a 30106 lb : a vehicle is stuck on the railroad tracks as a 30106 lb train is approaching with a speed of 75mph. as soon as the
Your friend decides to decrease cooking time for spaghetti : your friend decides to decrease cooking time for spaghetti noodles by adding table salt to 2.0 l water. how much table
How much heat is produced in burning 7 mol of rmc2 rmh2 : how much heat is produced in burning 7 mol of rmc2 rmh2 under standard conditions if both reactants and products are
Assume a thermocouple which supplies the input to an : assume a thermocouple which supplies the input to an analog input module generates a linear voltage from 20mv to 50mv
A closed rigid tank whose volume is 15 m3 contains : a closed rigid tank whose volume is 1.5 m3 contains refrigerant 134a initially a two phase lipuid-vapor mixture at 10c.
If the aluminum block is initially at 25 what is the final : suppose that 1.04 of rubbing alcohol evaporates from a 57.0 aluminum block. if the aluminum block is initially at 25
How would you develop a looping program in mips that will : how would you develop a looping program in mips that will take a series of decimal numbers and arrange them in
A proton in a linear accelerator has a de broglie : a proton in a linear accelerator has a de broglie wavelength of 115 rm pm. what is the speed of the
A gas occupies 404 l at 860 torr and 10c what volume will : a gas occupies 4.04 l at 860 torr and 10c. what volume will it fill if the pressure is changed to 731 torr and the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What would be the minimum coefficient of friction

If the curve were not banked, what would be the minimum coefficient of friction between tires and road that would keep traffic from skidding out of the turn when traveling at 85 km/h?

  Find out the largest couple that can be applied

Determining the largest couple that can be applied to a beam in pure bending. A beam of cross section shown is extruded from an aluminum alloy for which σy = 310 MPa and σu = 480 MPa.

  What type of feedback data should we be collecting

what type of feedback data should we be collecting; in order to make sure that our MPS data, our MRP data, our Aggregate Planning, etc. are all correct?

  Explain why the two measurements give different values

A similar measurement is made applying the force parallel to one of the cube axes. Explain why the two measurements give different values of the elastic modulus.

  Find the final mass of air

A balloon behaves so the pressure is P = C2V1/3, C2 = 100 kPa/m. The balloon is blown up with air from a starting volume of 1 m3 to a volume of 3 m3. Find the final mass of air assuming it is at 25oC and the work done by the air.

  How long is required for half the ice cube to melt

how long is required for half the ice cube to melt? State clearly all the assumptions you make in formulating your model of this problem.

  Determine the reactions of simply supported

Determine the reactions of simply supported beam to both a concentrated and uniform load. A beam with a span of 21 ft is simply supported at the left-hand end and fixed at the right-hand end.

  What stress is requireed to strain a sample

How much work(J)is done in a natural rubber filament when strains slowly and non reversely to a= 2?

  Find the discharge coefficient for flange taps

the reynolds number of a fluid flowing through a 5-cm-diameter, square-edged orifice plate meter within a 15-cm pipe is 250,000. Find the discharge coefficient for flange taps.

  Calculate the work transferred from the surroundings

Define your system to be the gas in the cylinder, and calculate the work transferred from the surroundings to the system from this expansion. Note that the pressure will change as the expansion takes place.

  Why is correct tightening of friction grip bolts important

why is the correct tightening of friction grip bolts important?

  Theory and practice of the product

Derive at least four concept designs to satisfy the given specification. Use short written descriptions and simple sketches to illustrate your ideas

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd