A civil engineer must design a wheelchair accessible ramp

Assignment Help Mechanical Engineering
Reference no: EM13344800

A civil engineer must design a wheelchair accessible ramp next to a set of steps leading up to a building. The height from the ground to the top of the stairs is 2ft. Based on ADA codes , the slope must be 1:12 or less. Slope is equal to the rise of the ramp divided by the run of the ramp.

The question is : using the known height and calculated base length what is the length of the slope of the ramp 

Reference no: EM13344800

Questions Cloud

The rigid gate oab of fig p258 is hinged at o andnbsprests : the rigid gate oab of fig. p2.58 is hinged at o andnbsprests against a rigid support at b. what minimum
Calculate the energy for vacancy formation in al given that : calculate the energy for vacancy formation in al given that the equilibrium number of vacancies at room temperature 25
The truck at b is used to hoist the cabinet up to the : the truck at b is used to hoist the cabinet up to the fourth floor of a building using the rope and pulley arrangement.
A weight attached to a spring of stiffness 525nm has a : a weight attached to a spring of stiffness 525nm has a viscous damping device. when the weight is displaced and
A civil engineer must design a wheelchair accessible ramp : a civil engineer must design a wheelchair accessible ramp next to a set of steps leading up to a building. the height
An airplane flies horizontally at 550 ms its : an airplane flies horizontally at 55.0 ms. its propellernbspdelivers 1500 n of thrust forward force to overcome
If the columns cross sectional area were uniform the : suppose that you want to design a column to support a uniform compressive stress stress naught. if the columns cross
How does temperature affect the separation of strands in gc : how does temperature affect the separation of strands in gc content71 verus gc content of 45. which will require a
What is the magnitude and direction of the force that must : you are swinging your younger sister in a circle of radius .9m. if her mass is 24kg and you arrange it so she makes one

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine how much load this boat can carry without sinking

The hull of a boat has a volume of 150 m3, and the total mass of the boat when empty is 8560 kg. Determine how much load this boat can carry without sinking (a) in a lake and (b) in seawater with specific gravity of 1.03.

  What is the relationship between la and lb

Two simple pendulums are related as follows. Pendulum A has a length LA and a bob of mass mA; pendulum B has a length LB and a bob of mass If the period of A is twice that of B, What is the relationship between LA and LB?

  Determine the energy change if the system mass

For the process where q= 62.5 kj/kg and wkcs= 60 kj/kg determine the energy change if the system mass is 2 kg.

  Hot water is pumped through a plate heat exchanger the hot

hot water is pumped through a plate heat exchanger. the hot water side of the heat exchanger consists of 16 plates of

  Will the engineers decide to use the steel

Assume they test null hypothesis H0: versus H1: Will the engineers decide to use the steel if H0 is rejected? Will the engineers decide to use the steel if H0 is not rejected?

  Calculate the force required to hold the gate closed

the gate in the is hinged at H.the gate is 2 m wide and normal to the palne of the diagram.calculate the force required to hold the gate closed.

  An open feedwater heater operates steadily with 30 kghr of

an open feedwater heater operates steadily with 30 kghr of liquid water entering one inlet at 40 degcnbspand 700 kpa.

  Determine the speed at which it strikes the ground at b

the snowmobile is traveling at 10m/s when it leaves the embankment at A.determine the speed at which it strikes the ground at B and its maximum acceleration along the trajectory AB.

  Why are tangent points so important when sketching

why are tangent points so important when sketching, drawing on paper with instruments, or using cad?

  Describe how you implement it using an open-loop system

Describe how you would implement it using an open-loop system

  The molar heat capacity of liquid iron exceeds that of iron

the molar heat capacity of liquid iron exceeds that of iron vapor by 2.5222calkthe molar heat of evaporation of liquid

  Measuring fracture toughness

Aim of this demonstration is to use measurements of the load required to propagate a crack (tear) in packaging tape to determine its fracture toughness and Describe the fracture behaviour of the insulation tape loaded with a small crack. Explain w..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd