A cantilever beam member made from steel with hollow

Assignment Help Mechanical Engineering
Reference no: EM13644190

A cantilever beam member made from steel with hollow circular cross section experiences an axial load of 300 KN (F1), and a vertical load of 200 kN (F2) as shown in the following figure.
The outside diameter of the beam is 50mm and the uniform wall thickness of the cross section is 4mm. Beam is made out of AISI 1040 Cold-drawn steel.

For the given system:
a. Draw the Free-Body-Diagram of the beam.
b. Compute the reaction forces and bending moment on the beam.
c. Compute the maximum normal stress, minimum normal stress and maximum shear stress.
d. Compute the maximum axial deformation on this member (x).
e. Compute the maximum vertical deflection of the tip of the beam due to the bending moment (y).
f. Will the member experience permanent deformation or complete failure due to this applied load? Draw your conclusions based on the strength values of the beam material.

Reference no: EM13644190

Questions Cloud

An air conditioner running with r-134a on a cycle executed : an air conditioner running with r-134a on a cycle executed under the saturation dome between the pressure limits of 0.8
Suppose that a data set has a minimum value of 24 and a : suppose that a data set has a minimum value of 24 and a maximun of 79 and that you want 5 classes. explain how to find
What is the balanced chemical reactions when carbon : what is the balanced chemical reactions when carbon dioxide reacts with water? how can carbon dioxide change the ph of
A uniform electric field with a magnitude of 6270 nc points : a uniform electric field with a magnitude of 6270 nc points in the positive x direction. find the change in electric
A cantilever beam member made from steel with hollow : a cantilever beam member made from steel with hollow circular cross section experiences an axial load of 300 kn f1 and
If a homeowner maintains their house at 68f what outside : a power company converts 40 percent of the heating value of the oil it uses into electric power. homeowners can buy
How does the excess co2 gas in the atmosphere cause the : 1. what is the greenhouse effect?2. how does the excess co2 gas in the atmosphere cause the greenhouse effect?3. what
When using the normal approximation to the binomial what is : when using the normal approximation to the binomial what is the standard deviation for a binomial probability
A 3 ft3 adiabatic rigid container is divided into two equal : a 3 ft3 adiabatic rigid container is divided into two equal volumes by a thin membrane. initially one of these chambers

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd