User Account

All Pages

A bar of high strength aluminum alloy is 150 mm long and

Assignment Help Mechanical Engineering
Reference no: EM13630638

A bar of high strength aluminum alloy is 150 mm long and has a circular cross section of diameter 40mm. It is subjected to a tensile load of 250kN, which gives a stress well below the material's yield strength. Determine the following: a) stress in the length direction, b) Strain in the length direction, c) strain in the transverse direction, d) length while under load e) diameter while under load.

Reference no: EM13630638

Questions Cloud

Cld water cp 418 kjkgc leading to a shower enters a : cold water cp 4.18 kjkgc leading to a shower enters a well-insulated thin walled double-pipe counter-flow heat
The energy generated within the house from people lights : a heat pump keeps the air temperature in a house at a temperature of 22.5 oc. the house is losing heat to the outside
To a closed system we add 28 kj of heat while its internal : a to a closed system we add 28 kj of heat while its internal energy decreases by 24 kj. how much work do we gain or
If the plant uses 287 kgs of coal as its fuel and coal has : a coal-fired power plant uses a large lake for its cooling needs. the power plant output is 300.0 mw. if the plant uses
A bar of high strength aluminum alloy is 150 mm long and : a bar of high strength aluminum alloy is 150 mm long and has a circular cross section of diameter 40mm. it is subjected
Steam enters an adiabatic turbine at 3 mpa and 350 celsius : steam enters an adiabatic turbine at 3 mpa and 350 celsius and leaves the turbine at 75 kpa with a quality of 89. if
How much is the mass rate for the outlet gases that is : 1 for the piping diameter changes and flow directions shown below if the velocity at the input is 5 ms the initial
Find the horizontal component of the average force on the : a bat strikes a 0.145-kg baseball. just before impact the ball is traveling horizontally to the right at 60.0ms and it
The length of the road up the hill is 263 m what should be : a 1010-kg car is being driven up a 6.03 deg hill. the frictional force is directed opposite to the motion of the car

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the corrosion rate in mpy

Calculate the corrosion rate in mpy, pm/y, and mdd. What is the ranking of this carbon steel in this acid environment and determine the effect of time on the solution corrosiveness and the carbon steel corrodibility.

  Determine the velocity of each block

Block A has a mass of 3 kg and B has a mass of 5 kg. If the system is released from rest, determine the velocity of each block in t=4s. Neglect the mass of the pulleys.

  Determine the normal and shearing stresses

Two forces are applied to the pipe AB as shown. Knowing that the pipe has inner and outer diameters equal to 35 mm and 42 mm, respectively, determine the normal and shearing stresses at (a) point a, and (b) point b

  The undeformed length of the spring is l knowing that the

a spring ab of constant k is attached to a support a and to a collar of mass m. the undeformed length of the spring is

  Dtermine the following a the mass kg and volume m3 of the

a piston - cylinder device initially contains 0.1 m3 of nitrogen gas at 150 kpa and 130 degc. the nitrogen is now

  Determine the heat transfer for this process

during this process heat is exchanged with surrounding such that the entire air remains at 30 degree celsius at all times.determine the heat transfer for this process.

  Find reciprocal lattice of the body-centred cubic structure

What is the minimum energy in the conduction band, and where can it be found in the Brillouin zone?

  Looking at the different convergence methods which

looking at the different convergence methods which convergence method polynomial order andor meshing would you

  Determine the corresponding velocity of slider b when

the rod of the fixed hydraulic cylinder is moving to the left with a constant speed. determine the corresponding

  The coefficient of friction of the metal against the dies

a cylinder of metal that is originally 100mm tall and 50mm in diameter must be open die forged to a height if 50mm. the

  Air is adiabatically compressed in a non flow process from

air is adiabatically compressed in a non flow process from a pressure of 14.7 psia and temperature of 70 degrees to 200

  What was the specific work done by the fan on the gas for

a wind tunnel draws atmospheric air at 20c and 101.3 kpa by a large fan located at the exit of the tunnel. a if the air

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd