What minimum angular velocity is necessary to keep the water

Assignment Help Civil Engineering
Reference no: EM13320156

A bucket full of water is to be rotated in the vertical plane. What minimum angular velocity, in rad/s, is necessary to keep the water inside if the rotating arm is 120 cm?

Reference no: EM13320156

Questions Cloud

What is the torque on the loop : A circular loop carrying a current of 1.0A is oriented in a magnetic field of 0.35 T. What is the torque on the loop when its plane is oriented at a 25 degree angle to the field
How to assume a weight od 150 pcf for reinforced concrete : it carries a uniform service load of 2450 lb/ft in addition to its own weight. material strengths are f'c=4000psi and fy=60000psi .assume a weight od 150 pcf for reinforced concrete.
Estimate the amplitude of the wave : A sinusoidal wave travels along a stretched string. A particle on the string has a maximum velocity of 0.900m/s, What is the amplitude of the wave
Best measure of actual and potential value : What are like to be the best measure of actual and potential value
What minimum angular velocity is necessary to keep the water : A bucket full of water is to be rotated in the vertical plane. What minimum angular velocity, in rad/s, is necessary to keep the water inside if the rotating arm is 120 cm
Find the new angular speed of the merry-go-round : A merry-go-round (I= 500 kg m^2) of radius R = 2 meters is rotating about a frictionless pivot, making one revolution every 5 seconds. Find the new angular speed of the merry-go-round
Design a line of sweaters : You have decided to design a line of sweaters
Calculate required compressive strength for a concrete mix : Calculate the required compressive strength for a concrete mix design if F'c = 5000 psi and data indicate a standard deviation of 600 psi based on 15 tests for a similar concrete mix
Find the angular acceleration of the stick : A uniform thin disk (I=1/3ML^2) of length L and mass M is pivoted at one end. It is held horizontal and released. Find the angular acceleration of the stick immeidately after it is released

Reviews

Write a Review

Civil Engineering Questions & Answers

  Find shear stress on each bolt and bearing stress on the bar

Due to an error, the length L shown was 1.795 m instead of 1.80 m, thus there is a gap of 0.5 cm, which makes it difficult to bolt the bar on the structure. The engineer suggests the bar is heated up by - Delta in order to close the gap.

  Calculate the alkalinity due to hco3- and co3-2

A water sample has phenolphthalein alkalinity (PPA) of 30 mg/L as CaCO3 and total alkalinity (TA) of 84 mg/L as CaCO3. If OH alkalinity is 5.3 mg/L as CaCO3, Calculate the alkalinity due to HCO3- and CO3-2.

  Determine what is the probability that all eight bits are 1

In a random pattern of eight bits used to test a micro-circuit, each bit is equally likely to be 0 or 1. Assume the values of the bits are independent. a. What is the probability that all eight bits are 1

  Determine what should the viscosity of the model fluid be

In the late 1990's the U.S. Army Corps of Engineers designed an experiment to model the flow of the Tennessee river downstream of the Kentucky Lock and Dam.

  How can the water pressure in a pipe be measured simply

1.How can the water pressure in a pipe be measured simply 2.What force causes the water pressure to fall as it flows along a pipe 3.How do you think the pressure drop will change when each of the three variables changes

  Estimate the daily emissions of particles from a solid-waste

The incinerator burns 50 tonnes per day (1 tonne= 1 metric ton= 1000kg) and exhausts gases in a ratio of 20kg of gases per kg of feed. Assume the gases exit at 200*C and 1atm.

  Determine the time rate of change of pressure at x

A gas flows along the x axis with a speed of v = 5x m/s and a presure of p = 10x^2 N/m^2, where x is in meters. a) Determine the time rate of change of pressure at the fixed location x = 1.

  Calculate the mass fractions of the phase present at 700 c

A 50 mg-50 Pb alloy is cooled slowly from 700 C to room temperature, a) Calculate the mass fractions of the phase present at 700 C

  Determine how many lamps are required for a flow

A membrane biological treatment plant effluent must be disinfected to what level prior for use as unrestricted recycled water. For a flow of 4 mgd and peak flow of 6 mgd, how many lamps are required

  Determine what is the angular rotation rate of the car

A car is travleing towars a 20 degree slope at 60 mph. The wheels have a radius of 12 in. and the car's wheelbase is 100 in. What is the angular rotation rate of the car immediately after the front wheel contacts the slop

  Explain will the vertical curve meet minimum ssd standards

A particular crest vertical curve has long been criticized as being unsafe. Its length is 400 ft. The prevailing speed on the crest vertical curve is 50 mph. In its present condition, its tangent grades are +2% and -3%.

  Calculate the pressure and piezometric head at the surface

An open top tank contains a layer of SAE 30 oil 0.5 m thick, a layer of water 0.7 m thick, and a layer of mercury 0.3 m thick. Calculate the pressure, and the piezometric head at the free surface, at both interfaces, and at the tank bottom.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd