What is the required flow rate of air through the turbine

Assignment Help Civil Engineering
Reference no: EM13304756

Compressed air at 400 kPa and 27C is used to drive a small high-speed turbine. The power output of the turbine is just 0.1 kW. If the process is adiabatic and steady, what is the required flow rate of air through the turbine if the exit state is 100 kPa and - 53 C. Assume negligible change of kinetic energy through the turbine and that air may be approximated as an ideal gas.

Reference no: EM13304756

Questions Cloud

Determine the interest rate : Determine the interest rate that would require a monthly total payment that is less than your current total payment. Also, refinancing costs you $2000 up-front in closing costs.
How wide will that diffraction maximum be : A two-slit apparatus is covered with a red (643 nm) filter. When white light is shone on the filter, on the screen beyond the two-slit apparatus, how wide will that diffraction maximum be
What is the maximum sales growth rate the company : Last year Montero Corporation had $850 million of sales, and it had $425 million of fixed assets that were used at only 60% of capacity. What is the maximum sales growth rate the company could achieve before it had to increase its fixed assets?
What is the final volume of the container : Some hydrogen gas is enclosed within a chamber being held at 200 degrees C with a volume of 0.025 m^3. What is the final volume of the container
What is the required flow rate of air through the turbine : The power output of the turbine is just 0.1 kW. If the process is adiabatic and steady, what is the required flow rate of air through the turbine if the exit state is 100 kPa and - 53 C.
Find the magnitudes of the average force on the wall : A 130 g ball with speed 7.5 m/s strikes a wall perpendicularly and rebounds in the opposite direction with the same speed. find the magnitudes of the average force on the wall
Identify which of the expenses are deductible : Assume all of the same facts as in Part a., except that Roberta is self-employed. Identify which of the expenses are deductible, and indicate whether they are deductions for or from AGI.
Determine the heat transfer rate from the compressor : In a refrigeration system Refrigerant 22 enters the compressor at 150 kPa and -10 C. It leaves the compressor at 1.0 MPa and 90 C. Assume the mass rate of flow through the compressor is 0.016 kg/s
What is the beta of the portfolio : You have decided to sell Creative Crafts for $4,000 and to use the proceeds to buy $4,000 of International Steel stock with a beta of 2.5.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Foundation raft of water tower

A circular rc girder for the foundation raft of water tower has dia 10m.the udl load transmittedby 8 coloumn on te girder being 300 kn/m.the width of the beam is 500 mm and the over depth.

  Determine dead load in pounds per linear foot from concrete

A three span continuous beam has spans of 27, 30, and 27 feet. The beams support one-way slabs, 6 inches thick that span 20 feet center to center. Assume that the beams are 16 inches wide and 24 inches deep.

  Cstr reactors of equal volume in series

Compare the total reactor volume required for 90% removal of the same pollutant in a CSTR system that contains a single reactor against a system that contains three CSTR reactors of equal volume in series.

  Determine the magnitude of the total acceleration at time t

Knowing that its speed continues to increase at the same rate until it reaches 100 km/h at point C, 1) determine the speed at point B, and 2) the magnitude of the total acceleration when t = 20 seconds.

  Discuss the dangers of optimization in terms of min section

Discuss the dangers of optimization in terms of minimum section to support loads. In other words, how would optimizing for bending stresses affect the shear capacity of a section

  What maximum load can be applied tot the center of the beam

A simply supported steel 'I beam' is made of three 1"*8" plates with a mass of 898.4 lbmass each as shown in I beam form. Steel has a modulus of elasticity of 30*10^6 psi. The beam is allowed to deflect 1.05 inch.

  Calculate aeration basin size and the wate sludge rate

A completely mixed activated-sludge plan is being designed for a wastewater flow of 3.0 mgd. The BOD of 225 mg/l is 200 mg/l soluble. The effluent soluble BOD requirement is 7 mg/l (70 percent of the total 10 mg/l).

  Find final velocity in mph if the drop height is increased

given: Vf=Vi + a t and Sf=Si + Vi t + 1/2 a t a= 27 ft/sec^2 accelerates from 10 mph to 93 mph in 4.5 seconds designers decided to modify the rise to become the tallest roller coaster in the world, find final velocity in mph if the drop height is ..

  What will be the total vehicle delay

Assuming D/D/1 queuing, what will be the total vehicle delay?

  Calculate ph of buffer solution prepared by mixing water

Calculate the pH of a buffer solution prepared by mixing 8.5g KH2PO4 with 43.5g K2HPO4 in 1 liter of water (this is actually the composition of the dilution water used in a BOD test. Follow the same procedures you have been using for previous acid/..

  Determine the factor of safety against overturning

The factor of safety is defined as the ratio of the stabilizing moment divided by the overturning moment. The densities of concrete and water are = 2.40 and = 1 , respectively. Assume that the dam does not slide.

  Determine what is the book value at the end of year 3

A hybrid car has a initial cost of $70,000 is to be depreciated by the straight-line method over a six years. The asset will a salvage value of $10,000. According to the straight line method, the book value at the end of year 3 is

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd