Steam enters the high-pressure turbine

Assignment Help Mechanical Engineering
Reference no: EM13713251

In a reheat-cycle power plant, steam enters the high-pressure turbine at 5 MPa, 450°C, and expands to 0.5 MPa, after which it is reheated to 450°C. The steam is then expanded through the low-pressure turbine to 7.5 kPa. Liquid water leaves the condenser at 30°C, is pumped to 5 MPa, and returned to the steam generator. Each turbine is adiabatic, with an isentropic efficiency of 87%, and the pump efficiency is 82%. If the total power output of the turbines is 10,000 kW, determine (a) the mass flow rate of the steam, (b) the pump power input, and (c) the power plant thermal efficiency. Please indicate on a diagram.

Reference no: EM13713251

Questions Cloud

How much work is done on the canister : The only force acting on a 4.2 kg canister that is moving in an xy plane has a magnitude of 5.3 N. How much work is done on the canister by the 5.3 N forces during this time.
Vapor power plant operates at steady state : A well-insulated tank in a vapor power plant operates at steady state. Water enters at inlet 1 at a rate of 125lb/s at 14.7lbf/in^2. Make up water to replenish steam losses from the plant enters at inlet 2 at a rate of 10 lb/s at 14.7 lbf/in^2 and 60..
Rate of heat transfer to the steam in the reheater : Air enters a compressor at 105 kPa and 300 K with a volumetric flow rate of 12 m3 /min and exits at 1200 kPa and 400 K. Heat transfer occurs at a rate of 2 kW from the compressor to its surroundings. Assuming ideal-gas behavior for air, steady flow, ..
What net torque must be applied to the wheel : A small grinding wheel has a moment of inertia of 4.0×105kg.m2. What net torque must be applied to the wheel for its angular acceleration to be 150rad/s2.
Steam enters the high-pressure turbine : In a reheat-cycle power plant, steam enters the high-pressure turbine at 5 MPa, 450°C, and expands to 0.5 MPa, after which it is reheated to 450°C. The steam is then expanded through the low-pressure turbine to 7.5 kPa. Liquid water leaves the conden..
Calculate the new pressure of the gas : A 3-Litre vessel contains gas at a pressure of 200 kPa. Five litres of gas at the same pressure is forced into the vessel. Calculate the new pressure of the gas. Use V1 = 8L, V2 = 3L
Air enters an automotive supercharger : Air enters an automotive supercharger at 100 kPa and 300 K and is compressed to 150 kPa. the efficiency is 70%. What is the required work input per kg of air?
Diamond shaped airfoil oriented to the oncoming stream : Consider a diamond shaped airfoil oriented to the oncoming stream. Approximate results since the inclination angles are small. All four faces are same length. Angle of attack is 10 deg. According to Newtonian hypersonic theory, Find the numerical val..
What is the electonic field at 9cm from the center : What is the E- field 9cm from the center along the symmetry axis of a charged ring with Q=25nC and R=12cm Let k= 9x109

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd