Same length between supports as the length of the paper roll

Assignment Help Mechanical Engineering
Reference no: EM13718448

A paper mill processes rolls of paper having a density of 984 kg/m3. The paper roll is 1.50 m outside diameter (OD) x 22 cm inside diameter (ID) x 3.23-m long and is on a simply supported, hollow, steel shaft. Find the shaft ID needed to obtain a maximum deflection at the center of 3 mm if the shaft OD is 22 cm. Assume the shaft to be the same length between supports as the length of the paper roll.

Reference no: EM13718448

Questions Cloud

Three-point bending test was performed on a glass specimen : A three-point bending test was performed on a glass specimen having a square cross-section of 15 mm length on each edge. The specimen fractured at a load of 4770 N when the distance between the support points was 41 mm.
Reduce crack length and increase tip radius : The fracture strength of glass may be increased by etching away a thin surface layer. It is believed that the etching may alter the surface crack geometry (i.e. reduce crack length and increase tip radius). Calculate the ratio of the etched and origi..
Determine temperature in celsius of equilibrium ice water : Estimate the slope dp/dt of the ice +water line using the triple point information. Specific entropy of ice at the triple point is -1221J/kgK , specific entropy of liquid water at triple point is 0.0 J/kgK. Determine therefore the temperature in Cels..
Specific heat at constant pressure of the saturated liquid : Show that the specific heat at saturation of a liquid phase of mass m (defined by Cf= (deltaQ/m)dt is generally not the same as the specific heat at constant pressure of the saturated liquid.
Same length between supports as the length of the paper roll : A paper mill processes rolls of paper having a density of 984 kg/m3. The paper roll is 1.50 m outside diameter (OD) x 22 cm inside diameter (ID) x 3.23-m long and is on a simply supported, hollow, steel shaft. Find the shaft ID needed to obtain a max..
Create a segment of a recognizable tune consisting : Create a segment of a recognizable tune consisting of 5-6 notes, possibly with spaces in between. Search web sources to find the frequencies of familiar music notes (for example the frequency of A4 is 440Hz, of A5 is 880Hz, of C5 is 523.25Hz).
Relationship between independent variables and deflection : The bottom of a large, 5-gallon plastic bucket bows when the bucket is filled with water. The deflection of the bottom surface, ?, is a function of the bucket diameter, D, the depth of water, h, the specific weight of the water, ?, the thickness of t..
Heat transfer coefficient between water and surroundings : A hot-water cylinder contains 150 liters of water. It is insulated, and its outer surface has an area of 3.5 m^2. It is located in an area where the ambient air is 250C, and the overall heat transfer coefficient between the water and the surroundings..
Determine the actual heat transfer rate : A shell and tube heat exchanger with one shell pass and four tube passes is being analyzed to determine the heat transfer rate and the fluid outlet temperatures for prescribed flow rates and inlet temperatures. The cold fluid has a heat capacity rate..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd