Pressure-angle helical pinion with a right-hand helix

Assignment Help Mechanical Engineering

Reference no: EM13714087

A 17-tooth 20 normal pressure-angle helical pinion with a right-hand helix angle of 30 rotates at 1800 rev/min when transmitting 4 hp to a 52-tooth helical gear. The normal diametrical pitch is 10 teeth/in, the face width is 1.5 in, and the set has a quality number of 6. The gears are straddle-mounted with bearings immediately adjacent. The pinion and gear are made from through-hardened steel with surface and core hardness of 240 Brinell on the pinion and surface and core hardness of 200 Brinell on the gear. The transmission is smooth, connecting an electric motor and a centrifugal pump. Assume a pinion life of 10^8 cycles and rim thickness factor (KB) is equal to 1.00 and a reliability factor (KR) is equal to 0.85 for both pinion and gear. Perform stress analysis (bending and contact) for both pinion and gear and determine factor of safety of gears in bending.

Reference no: EM13714087

Questions Cloud

Required for annealing process using lumped system analysis : A long steel bar of radius R = 2.5 cm, k =50 W/(m .°C), p = 7800 kg/m3, and c = 0.5 kJ/(kg. .°C) is to be annealed by cooling slowly from 800.°C to 100.Â°C in an environment at temperature 50.°C. If the heat transfer coefficient between the environme..

Steam power plant operates between the pressure limits : A steam power plant operates between the pressure limits of 4.5MPa and 15kPa. Steam enters the pump as saturated liquid and leaves the turbine as saturated vapor. Determine the ratio of the work delivered by the turbine to the work consumed by the pu..

Fluid flow axially in annular region between two concentric : A fluid flow axially in the annular region between two concentric pipes with radii R1 and R2>R1, respectively. Assume the flow is steady, incompressible, axisymmetric, fully-developed, and has no swirl. Also neglect all body forces.

Assume that the tunnel operates adiabatically : A hypersonic gun tunnel is used to generate short-duration, high-speed flows and typically consists of two cylindrical volumes separated by a diaphragm. One end of the tunnel (the driver end) is pumped to a high pressure, while the other end (the dri..

Pressure-angle helical pinion with a right-hand helix : A 17-tooth 20 normal pressure-angle helical pinion with a right-hand helix angle of 30 rotates at 1800 rev/min when transmitting 4 hp to a 52-tooth helical gear. The normal diametrical pitch is 10 teeth/in, the face width is 1.5 in, and the set has a..

Analysis for both pinion and gear-hardness values : A cable drum for a crane is to rotate between 160 and 166 rpm. Design a gear drive for 25 hp in which the input pinion rotates at 925 rpm and the output rotates with the drum. The crane is expected to operate with a 50% duty cycle for 120 hours per w..

Determine the rate of heat transfer to the rods in the oven : Long cylindrical steel rods (p=7833kg/m3 and cp=0.465kJ/kg*°C) of 8-cm diameter are heat treated by drawing them at a velocity of 4m/min through an 8-m-long oven maintained at 900°C. If the rods enter the oven at 25°C and leave at 750°C,

Find the horsepower to circulate the flow : Consider a recalculating flow in the power cycle shown in the figure. The fluid flowing in 100 ft of smooth pipe have an average specific weight of 50 lbf/ft3 and average dynamic viscosity of 5×10-4 lbf.s/ft2. Head loss in the nuclear reactor is 75 f..

Determine the velocity of the air at the inlet : At steady state, air at 200 kPa, 325 K, and mass flow rate of 0.5 kg/s enters an insulated duct having differing inlet and exit cross-sectional areas. The inlet cross-sectional area is 6 cm2. At the duct exit, the pressure of the air is 100 kPa and t..

User Account

All Pages