User Account

All Pages

Plunger of a hypodermic needle

Assignment Help Mechanical Engineering
Reference no: EM13871851

A 2.4-N force is applied to the plunger of a hypodermic needle. If the diameter of the plunger is 1.3 cm and that of the needle 0.20 mm,

(a) With what force does the fluid leave the needle?

(b) What force on the plunger would be needed to push fluid into a vein where the gauge pressure is 18mm-Hg? Answer for the instant just before the fluid starts to move?

Reference no: EM13871851

Questions Cloud

What is the correct definition of the term self-acceptance : What is the correct definition of the term self-acceptance
Absolute and gauge pressures : A 975-kg car has its tires each inflated to "32.0 pounds (a) What are the absolute and gauge pressures in these tires in lb/in.', Pa, and atm?
Statements about free play and organized play : Which of the following statements about free play and organized play is correct
What pressure does she exert on the floor : A 50.0-kg woman balances on one heel of a pair of high heeled shoes. If the heel is circular and has a radius of 0.500 cm, what pressure does she exert on the floor?
Plunger of a hypodermic needle : A 2.4-N force is applied to the plunger of a hypodermic needle. If the diameter of the plunger is 1.3 cm and that of the needle 0.20 mm,
How could an investment banker help lp achieve its objective : LP would prefer to have floating rate debt. The market is asking LIBOR + 100 bps. How could an investment banker help LP achieve its objective with a swap?
Marketing channel play a key role in marketing strategy why? : Marketing channels play a key role in marketing strategy because they
Discount for the computer would be the equivalent : The Byrd Company had the following transactions during 2010 and 2011:
Determine the equilibrium readings of both scales : A 1.00-kg beaker containing 2.00 kg of oil (density = 916.0 kg/m3) rests on a scale. A 2.00-kg block of iron is suspended from a spring scale and completely submerged in the oil as in Figure P14.63. Determine the equilibrium readings of both scale..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  On the basis of an air-standard analysis compare the values

air is considered as an ideal gas. dont use gas table for gas properties just assume that both cv and cp are constants.

  Design a v-belt drive for this application including sheave

a 2 hp electric motor running at 1720 rpm is to drive a blower at a speed of 240 rpm. design a v-belt drive for this

  Steam enters the turbine of a cogeneration plant at 7 mpa

steam enters the turbine of a cogeneration plant at 7 mpa and 500 degc. one quarter of the steam is extracted from the

  Etermine the force applied by the ram

A cube of 2" dimensions is placed in a square hole (also of 2" dimensions) that is 1.998" deep. The hole was cut out of a rigid material. (The top of the cube protrudes .002" above the surface). If a flat rigid plate is placed on top of the cube and ..

  Inflow rate is adjusted to match the outflow rate

Water is flowing into the top of a tank at a rate of 200 gpm. The tank is 18 in. in diameter and has a 3 in. diameter hole in the bottom, through which the water flows out. If the inflow rate is adjusted to match the outflow rate, what will the heigh..

  What is the outlet pressure if the inlet pressure is 100 mm

for a one order narrowing of arterial vessel in cross sectional area ainaout 10 what is the outlet pressure if the

  Suppose random variable

Suppose random variable X is normally distributed. Find the probability that X is less than 6 or X is at least 12...

  How many pump stations would be needed for a pipeline

200mm DN pipeline has to deliver 80m³/h of water at a discharge pressure of  5,550 kPa. Approximately how many pump stations would be needed for a pipeline 300km long?

  If these readings are 333k and 138kpa respectively and the

a diffuser in a jet airplane intake system is instrumented to give readings of stagnation temperature and stagnation

  Explain more about brittleness and is it better to use

yeild ocuurs then plastic deformation then rupture under cold work of steel the rupture allows leakage which relieves

  If the point of landing is 20 ft away determine the

during a race the dirt bike was observed to leap up off the small hill at a at an angle of 60o from the horizontal. if

  If z1-z205m what is the actual head rise across the pump

the performance characteristics of a certain centrifugal pump are determined from an experimental setup. when the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd