If the vessel had a yield strength in compression in equal

Assignment Help Mechanical Engineering
Reference no: EM13630612

The spherical bathyscaphe Trieste that took 2 people to the bottom of Challenger Deep was 7 feet in diameter.

If the vessel had a yield strength in compression in equal to that of 4340-HR steel (901 x 10^6Pa) and a safety factor of 2 was employed, what would the wall thickness need to be to withstand the pressure at the bottom of Challenger Deep (1086 atm) ?

Reference no: EM13630612

Questions Cloud

Heat is now added until the quality is 52 percent determine : a rigid 110-l steam cooker is arranged with a pressure relief valve set to release vapor and maintain the pressure once
The mean solar flux at the earths surface is 200 : the mean solar flux at the earths surface is 2.00 jcm-2min-1. in a nonfocusing solar collector the temperature can
Radium ra decays to radon rn which decays to polonium if at : radium ra decays to radon rn which decays to polonium. if at t 0 a sample is pure radium how much polonium does it
If the polymer has a shear modulus of 400 mpa and the tube : a biomedical application requires that a very thin layer of an elastic polymer should be loaded in pure shear with a
If the vessel had a yield strength in compression in equal : the spherical bathyscaphe trieste that took 2 people to the bottom of challenger deep was 7 feet in diameter.if the
Determine the turbine power output the fraction of the : a stationary gas turbine power plant operates on the brayton cycle and delivers 20 mw to an electric generator. the
At what pressuregive type tension compression or shear : a cylinder 10 feet long has an ouside diameter of 2 inches and a 1mm thick wall. the yield strength of the wall
If the surroundings are treated as a thermal reservoir what : water in 50 liter rigid container is initially at 500 kpa and 350c. as the result of heat transfer the water obtains
The pressure inside the cylinders of a diesel engine : the pressure inside the cylinders of a diesel engine reaches a maximum pressure of 100atm during combustion. the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What are the values of the lengths la and lb in state 1 the

cylinder a and cylinder b contain 0.07 grams of helium and 0.4 grams of oxygen respectively. each of these gases is

  Air flows through the brayton cycle with a mass flow rate

modified brayton cycle is to be analyzed using the air-standard assumption with constant specific heats at a

  I the coefficient of performance is 80 of the cop of

a refrigeration remove 12 kj of heat from a body when working between 24 k and 310 k if the coefficient of performance

  Air at 100 kpa and 27degc enters an isentropic compressor

air at 100 kpa and 27degc enters an isentropic compressor at a rate of 100 ls and leaves at 1000 kpa. determine the

  A 15-kg steel gas tank holds 300 l of liquid gasoline

a 15-kg steel gas tank holds 300 l of liquid gasoline having a density of 800 kgm3. if the system is decelerated with 6

  Where a is a scaling constant and v is the relative speed

wind drag can be approximated as being quadratic in speedfd av2where a is a scaling constant and v is the relative

  What is the pressure at any point at the bottom of the tank

A tank with a flat bottom is filled with water to a height of 3.5 meters. what is the pressure at any point at the bottom of the tank? (You can ignore atmospheric pressure when calculating your answer.)

  The outer surface of the heater is exposed to a fluid with

a very thin electric heater is wrapped around the outer surface of a long cylindrical tube whose inner surface is

  When the efficiency of an otto cycle will approach that of

when the efficiency of an otto cycle will approach that of carnot cycle? even with nest possible arrangements the

  What is the total energy released by burning the mass of

over a period of time a car engine burns 0.01kg of fuel equivalent to supply of qh from a high temperature reservoir at

  A vehicle traveling at 30 mph enters a 600 ft radius curve

a vehicle traveling at 30 mph enters a 600 ft radius curve and begins to increase its speed at a rate of 10 fts2. find

  An ideal diesel cycle with air as the working fluid has a

an ideal diesel cycle with air as the working fluid has a compression ratio of 20 and a cutoff ratio of 1.3. this cylce

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd