Find the normal sress and deformation in the wire

Assignment Help Civil Engineering
Reference no: EM13297841

a 10.0 inch long 10-guage wire of yellow brass (E=105 GPa) is subjected to an axial tensile force of 400 lbs. Find the normal sress and deformation in the wire. A 10-guage wire has a diameter of 2.588 mm.

Reference no: EM13297841

Questions Cloud

Calculate the kinetic energy of the particle : A particle undergoes uniform circular motion of radius 19.1 ?m in a uniform magnetic field. What is the kinetic energy of the particle
Effective competitive intelligence program : Most US companies generally agree they need an effective competitive intelligence (CI) program. What are four objectives of such an effective program? Discuss their dimensions and correlate their effectiveness on advancing the firm’s strategy.
How to calculate the concentrations of pcl5(g) : A 0.291 mol sample of PCl5(g) is injected into an empty 4.35 L reaction vessel held at 250 °C. Calculate the concentrations of PCl5(g) and PCl3(g) at equilibrium.
Compute the price of the bond : Compute the price of the bond
Find the normal sress and deformation in the wire : a 10.0 inch long 10-guage wire of yellow brass (E=105 GPa) is subjected to an axial tensile force of 400 lbs. Find the normal sress and deformation in the wire. A 10-guage wire has a diameter of 2.588 mm.
Would your advice depend on the maturity of individual bonds : You anticipate an increase in interest rates in the near future. How would you advise her? Would your advice depend on the maturity of individual bonds?
Calculate the mass of the meter stick : A meter stick balances horizontally on a knife-edge at the 50.0 cm mark. What is the mass of the meter stick
Determine the maximum number of large trucks and buses : The traffic stream consists of cars, buses, and large trucks (no recreational vechicles). A weekday directional peak-hour volume of 1800 vehicles (familar users) is observed, with 700 arriving in the most congested 15 min period.
Benefits are ignored in the capital budgeting process : What might happen if intangible benefits are ignored in the capital budgeting process? What steps can management take to incorporate these benefits into the capital budget evaluation process?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculating the force in a punch press

Calculate the force (in Kn) a punch press must exert if it is to punch out a large washer from a strip of 5-mm thick sheet steel with an ultimate shear strength of 400 MPa.

  What is the minimum distance from the stalled car

What is the minimum distance from the stalled car at which the driver could apply the brakes and still stop before hitting it? Assume coefficient of rolling resistance of 0.013.

  Calculate the distance traveled by the prey

Calculate the distance traveled by the prey from the time it is dropped until the time it hits the ground. Express your answer correct to the nearest tenth of a meter.

  Determine the design speed of the curve

an equal-tangent sag vertical curve is designed with the PVC AT STation 109 + 00 and elevation 950 ft, the PVI at station 110 + 77 and elevation 947.34ft,and the low point at station 110 + 50 . Determine the design speed of the curve.

  What is the probability that the second explosion

Cities cover approximately 0.5% of the Earth's land area, which itself constitutes 29% of the total surface of the planet. What is the probability that the second explosion in part (b) occurs over a city? Assume an equally likely probability of im..

  Purposes of assessing an economys growth performance

For the purposes of assessing an economy's growth performance, which is the more important statistic, real GDP or nominal GDP? Why?

  Find the optimal solution

The company would like to distribute the songs between the two CDs such that the used space on each CD is about the same. Formulate the problem as an IP, and find the optimal solution.

  Magnitudes of the additional loads

Determine the magnitudes of the additional loads that must be applied at B and F if the resultant of all six loads is to pass through the center of the mat.

  Tangential component of the acceleration of the sled

Knowing that the coefficient of kinetic friction between a sled and the run is 0.10 and that the speed of the sled is 25 ft/s at B, determine the tangential component of the acceleration of the sled a) just before it reaches B, b) just after it pa..

  Uva levels in raw and treated drinking water

My question is regarding UVA levels in raw and treated drinking water with regard to TOC and DOC removal. Is there a jar test procedure that incorporates the UVA values of the various stages of treatment and is there a document you could refer me ..

  What return period must an engineer use in the design

What return period must an engineer use in the design of a bridge opening for a 50% risk that flooding will occur at least once in two consecutive years? Repeat for a risk of 100%.

  Explain why the compressive strength of wood loaded

EXPLAIN BRIEFLY WHY THE COMPRESSIVE STRENGTH OF WOOD LOADED "PARALLEL" TO ITS GRAIN IS HIGHER THAN THE COMPRESSIVE STREGTH OF THE SAME WOOD LOADED "PERPENDICULAR" TO THE GRAIN

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd