Electrical work is employed to heat

Assignment Help Mechanical Engineering
Reference no: EM13713189

Electrical work is employed to heat 2kg of water from 298.15 K to 373.15 K. Determine the electrical work required, and the minimum work required (e.g., by using a heat pump instead).

 

The specific heat for water is 4.184 kJ/kgK and the ambient is at T = 298.15 K, 1 bar.

Reference no: EM13713189

Questions Cloud

Semi-circular cross-section with radius : A stiletto heel has a semi-circular cross-section with radius of 0.25 in. Due to walking over irregular surfaces and shifts in body weight, moments of up to 30 lb.-in. can act where the heel attaches to the shoe. Determine the maximum tensile or comp..
Rate of heat transfer between the steam and cooling water : A shell-and-tube heat exchanger is used to cool a flow of steam using a stream of cooling water. The steam enters the heat exchanger at 0.1 bar and a quality of 91% (state 1), and exits as a saturated liquid at the same pressure (state 2). The mass f..
Identify parameters : Read (a,b,c); if(a!=0){d=b*b-4*a*c;if(d
What is the angular velocity of the bicycle : A bicyclist starts at rest at the top of a 50.3m long hill. After a small push, he coasts speeding up with an acceleration of 3.43m/s2 due to the slope of the hill. What is the angular velocity of the bicycle tires at the bottom of the hill.
Electrical work is employed to heat : Electrical work is employed to heat 2kg of water from 298.15 K to 373.15 K. Determine the electrical work required, and the minimum work required (e.g., by using a heat pump instead).
Write a summary of the book born to buy : You need to write a summary of the book born to buy.
The crankshaft in a given automobile rotates : The crankshaft in a given automobile rotates, on average, at 2500 revolutions per minute for a period of 2 h per day. How long would it take before the crankshaft has been subjected to 10^8 load cycles?
Energy conservation and availability balance equation : Water vapor at 300 C, 35 bars (state 1) expands to 5.0 bars (state 2) using an adiabatic throttling valve. The ambient is at T = 25 C, 1 bar. Simplify the energy conservation and availability balance equation for the current problem. Calculate the ex..
What is the internal resistance of the battery : A battery has an emf of 15.0 V. The terminal voltage of the battery is 13.4 V when it is delivering 16.0 W of power to an external load resistor R. What is the internal resistance of the battery.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The forces acting on the block in motion

Draw a free-body diagram that identifies all the forces acting on the block in motion.

  What is the actual mechanical advantage of the system

what is the actual mechanical advantage of the system?

  Obtain a general relation for temperature distribution

consider a water pipe of length l17m inner radius r115cm outer radius r220cm and thermal conductivity k14wmk. heat is

  Determine the overall plant efficiency the ratio of net

consider a coal-fired steam power plant that produces 350 mw of electric power. the power plant operates on a simple

  Find the power to the air and how much air should be flowed

a power plant generates 150 mw of electrical power. it uses a supply of 1000 mw from a geothermal source and rejects

  Constant volume with u1-u3 -264 kj a draw p-v diagram b

a thermodynamic cycle consist of i 1-2 constant pressure process with p11.4 bar v1 0.028 m3 w1210.5 kj ii 2-3

  A 04 m3 rigid vessel initially contains a saturated

a 0.4 m3 rigid vessel initially contains a saturated liquid-vapor mixture of water at 100 c. the water is heated until

  Draw mohrs circle for a point on top of the cross-section

a simply supported beam of length 18 ft. is subjected to a trapezoidally distributed load that has a value of 3 kipft

  A compressor installed at a whalf for loading container

a compressor installed at a whalf for loading container ships is able to provide 6 bar.g pressure into the pressure

  Estimate the theoretical fracture strength

Estimate the theoretical fracture strength of a brittle material if it is known that fracture occurs by the propagation of an elliptically shaped surface crack of length 0.16 mm and that has a tip radius of curvature of 0.002 mm when a stress of 1..

  A roast is in an oven and weighs 225 kg it is initially at

a roast is in an oven and weighs 2.25 kg. it is initially at 6 degrees celsius and needs to be heated to 80 degrees

  The heat transferred to the condenser cooling water and the

1. steam is supplied dry saturated at 40 bar to a turbine and the condenser pressure is 0.035 bar. if the plant

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd