Consider two- dimensional-straight triangular fin of length

Assignment Help Mechanical Engineering
Reference no: EM13713499

Consider a two- dimensional, straight triangular fin of Length L= 50mm and base thickness t= 20mm. The thermal conductivity of the fin is k= 25 W/mK. The base temperature is T_b= 50 degrees Celsius, and the fin is exposed to convection conditions characterized by h= 50 W/m^2 K. T_infinity= 20 degrees Celsius.

1) Using the finite difference mesh delta x= 10mm and delta y= 2mm, and taking advantage of symmetry, determine the fin efficiency.

2) Make a temperature contour plot using MATLAB

Reference no: EM13713499

Questions Cloud

Determine the extra work required to stretch it : If it takes 4.00 J of work to stretch a Hooke's-law spring 10.0 cm from its unstressed length, Determine the extra work required to stretch it an additional 10.0 cm
Use the cubic spline method as well : An important fluid property is the kinematic viscosity which determines the viscous, or frictional, forces acting in a flow. The kinematic viscosity of air multiplied by 10^6 is given at 350, 450, 500, 550, and 650 K as 20.92,32.39, 38.79, 45.57, and..
Find the distance from the objective to object being viewed : The focal length of the eyepiece of a certain microscope is 18.0mm. The focal length of the objective is 8.00mm. Find the distance from the objective to the object being viewed
Find the work done by the shopper on the cart : A shopper in a supermarket pushes a cart with a force of 35.0 N directed at an angle of 25.0° downward from the horizontal. Find the work done by the shopper on the cart as he moves down an aisle 50.0 m long
Consider two- dimensional-straight triangular fin of length : Consider a two- dimensional, straight triangular fin of Length L= 50mm and base thickness t= 20mm. The thermal conductivity of the fin is k= 25 W/mK. The base temperature is T_b= 50 degrees Celsius, and the fin is exposed to convection conditions cha..
Find the maximum velocity in the tube : Water at 27 C flows through a tube of diameter d = 50 mm. If the flow is fully-developed and has a mass flow rate of 0.01 kg/s, find the maximum velocity in the tube, and the pressure gradient, dp/dx
Evaluate the thermal efficiency : A quantity of water within a piston-cylinder assembly executes a carnot power cycle. During ISOTHERMAL expansion, the water is heated from saturated liquid at 45 bar until it is a saturated vapor. The vapor then expands adiabatically to a pressure of..
Estimate what is the drag force on a car : What is the drag force on a 1.6 m wide, 1.4 m high car traveling at 11 m/s (25 mph)? Suppose that the density of air is 1.2 kg/m3
Insulated reactor operating at steady state-burns completely : Methane gas (CH4) at 25° C, 1 atm enters an insulated reactor operating at steady state and burns completely with  x % of theoretical air entering at 25°C, 1 atm. Calculate the adiabatic flame temperature (AFT) at x=100, 200, 300 and 400 % and plot t..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd