Compute the flux linkage as a function of time

Assignment Help Chemical Engineering
Reference no: EM131115170

The 50-turn coil in the configuration of Figure P12.1.3 is rotated at a constant speed of 300 r/min. The axis of rotation is perpendicular to a uniform magnetic flux density of 0.1 T. The loop has width w = 10 cm and length l = 1 m. Compute:

(a) The maximum flux passing through the coil.

(b) The flux linkage as a function of time.

(c) The maximum instantaneous voltage induced in the coil.

(d) The time-average value of the induced voltage. (e) The induced voltage when the plane of the coil is 30° from the vertical.

990_a30e9a7e-f2eb-4d62-8a1b-361cb1873e60.png

Reference no: EM131115170

Questions Cloud

Creating an ethical code : You are an entrepreneur who has decided to go into business and open a steak and chicken restaurant. Your business plan requires you to hire at least twenty people as chefs, waiters, and so on. As the owner, you are drawing up a list of ethical pr..
What are your specialties or areas of clinical focus : Do you have any special certifications or training beyond your original graduate coursework? How do you approach therapy or treatment? Do you use specific modalities, techniques, or interventions?
Are there differences between theory and practice : How does the Particulars in the movie conform to the theory on the areas identified above? Are there differences between theory and practice? If your answer is ‘yes' to the preceding questions, what are the reasons for these differences?
Extent of the machines : Shannon orally agrees to buy 500 telephones from Thomas for $2,000. Thomas delivers 1,500 phones to Shannon. She receives them and accepts them. Which of the following is correct with regard to this transaction. BE CAREFUL ABOUT THIS QUESTION!
Compute the flux linkage as a function of time : The 50-turn coil in the configuration of Figure P12.1.3 is rotated at a constant speed of 300 r/min. The axis of rotation is perpendicular to a uniform magnetic flux density of 0.1 T. The loop has width w = 10 cm and length l = 1 m
Describe a foot-in-the-door or door-in-the-face strategy : After you identify the group and the target behavior, explain whom you would try to change and what steps would be necessary to initiate commitment or reciprocity processes. Do you think this would lead to long-term change? Why or why not?
What are the conclusions and recommendations : What is the thesis (main idea) of the article? Why is (are) the author(s) writing about the topic? What facts are presented?What are the conclusions and recommendations?
Processing speed of cpu : Explain the different factors affecting the processing speed of CPU. Any body who understands computer?
The import of goods produced with badly paid labor : In order to protect consumers, the United States has taken action to restrict the imports of certain Chinese goods, such as toys that contain lead and seafood that does not meet certain health standards. Some say that this is a double standard. If th..

Reviews

Write a Review

Chemical Engineering Questions & Answers

  State the principles you apply in your designs

Lay out the flow sheet of the process and justify your choice based on the characteristics of the source water (note: if data not available, you can make your estimations based on other similar sites or commensense); (20%)

  Determine time for moisture to penetrate to center

Assuming that the two unsealed faces of the wood immediately jump to an equilibrium moisture content of 10 lb H20 per 100 lb of dry wood, determine the time for the moisture to penetrate to the center of the slab (2 in. from either face). Assume a..

  Conclusions about photosynthesis

When algae growing in water containing only 16O were furnished carbon dioxide containing 18O, no 18O was found to be evolved from the oxygen gas produced. What conclusions about photosynthesis can be drawn from these experiments?

  Close boiling points and the relative volatility

Propane is separated from propylene by distillation. The compounds have close boiling points and the relative volatility will be low.

  Calculate the total pressure drop due to friction

The line is commercial steel pipe, 25 mm internal diameter, length 120 m. The properties of the fluid are: viscosity 0.99 mNm-2 s, density 998 kg/m3. Calculate the total pressure drop due to friction when the flow rate is 3500 kg/h

  A vapor of titanium isopropoxide

A vapor of titanium isopropoxide (partial pressure = 133 pascal) is reacted in O2 rich CH4 flame at T=2000K. Calculate the diameter of the nuclei.

  The combustion of hydrogen and in the moisture

When burnt , the flue gas issuing out of the furnace at 545 oc analyses on dry basis as CO2 =14.5 % , O2 = 4.7%, N2 = 80.8 % , Other relevant data are- Gross C.V. of coal =28000 kj /kg , ambient temperature = 15oc

  Alcohol beverage technology describe the principles of a

describe the principles of a vapour adsorption refrigeration system and compare this to a vapour recompression system.

  Discussing the pros and cons of the process

Machining of composites can be classified as conventional machining and non-traditional machining. Among each category, there are many processes. Describe each of those processes, by giving the brief definition of the process, listing the machine..

  Explains the mechanism of catalysis

Explains the mechanism of catalysis.

  Determine the minimum number of stages required

Determine the minimum number of stages required, and determine the minimum reflux ratio

  What is the temperature at the end of the heating

A sealed rigid tank of 1 m3 capacity contains 1.2 kg of water at 1 bar and 99.63 °C. To this tank we add heat until the pressure increases to 3 bar. What is the temperature at the end of the heating?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd