Car accelerates from rest along a straight section of road

Assignment Help Mechanical Engineering
Reference no: EM13709779

A car accelerates from rest along a straight section of road. It starts at position s = 150 m and reaches a speed of 20 m/s at position s = 200 m. It is proposed that this acceleration, a, can be modelled as being a function of position, s, in the form a = c/s. With this model, what is the constant c?

Reference no: EM13709779

Questions Cloud

Where would the net electric field be zero : Two particles having charges of 0.550nC and 4.95nC are separated by a distance of 1.90m. Where would the net electric field be zero
Derive the expression for a simple spring mass system : Derive the expression for a simple spring mass system equation and its response. Plot the response for 3 different values of k, (k=1, k=10, k=100) assume mass M= 1, what are the natural frequencies in rad/sec and Hz for each case. Explain the differe..
Find the speed of transverse waves in the wire : A variable-length air column is placed just below a vibrating wire that is fixed at the both ends. Find the speed of transverse waves in the wire
Find the total force resisting the motion of the block : A 25-N block slides down a plane inclined at 21.2 degrees to the horizontal with constant velocity. Find the total force resisting the motion of the block
Car accelerates from rest along a straight section of road : A car accelerates from rest along a straight section of road. It starts at position s = 150 m and reaches a speed of 20 m/s at position s = 200 m. It is proposed that this acceleration, a, can be modelled as being a function of position, s, in the fo..
Ball is dropped inside an evacuated tube : A ball is dropped inside an evacuated tube so that there is no aerodynamic drag acting on the ball. At one point it is at a height of 2.5 m and is dropping at a speed of 1.0 m/s. What will be the height of the ball when its speed is 5.0 m/s? Take g= ..
How would you attempt to maximize patient satisfaction : How would community-based participatory research principles be reflected in the development of an intervention to promote the utilization of preventive health services by African-American men?
Obtain the minimum area plates of this capacitor can have : A parallel-plate capacitor is to be constructed by using, as a dielectric, rubber with a dielectric constant of 3.20 and a dielectric strength of 25.0MV/m. What is the minimum area the plates of this capacitor can have
Look for postings of technology-driven mergers : Use your favorite search engine on the Internet and look for postings of technology-driven mergers and acquisitions. What are the reasons given for the mergers and acquisitions? What is described as coming from each of the organizations? Are t..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine a temperature quality and the volume in m3 of the

20 kg of water at 200 kpa with a quality 25 is heated under a constant volume process until its pressure reaches 400

  Determine mud height at which blocks will overcome friction

Mud is stopped using a wall made from 1.2 m high x 0.25 m wide rectangular concrete blocks as shown in figure below. Blocks density is 2700 kg/m3, mud density is 1800 kg/m3, and friction coefficient between ground and concrete blocks is f = 0.3.

  The valve is closed when no liquid is left in the tank and

a tank is rigid and contains r134a at 800 kpa and saturated conditions with quality equal to .75. from this condition a

  A piston-cylinder device contains liquid and vapor water in

a piston-cylinder device contains liquid and vapor water in equilibrium at a pressure of 14.7 psia. the mass of the

  Determine the rate of entropy generation of the steam

steam enters an adiabatic turbine at 8 mpa and 520 degc with a volumetric flow rate of 0.8 m3s and exits at 30 kpa. the

  The temperature is 68 f and the velocity is 40 fts the exit

a pump steadily draws water at a mass flow rate of 20 lbms through a piping arrangement. the pressure at the inlet is

  If the maximum surface flaw size can be reduced to 30 mm

a component is fabricated from an aluminum alloy that has a plane strain fracture toughness of 43 mpa-m-12. during

  A 01 m long mullite furnace tube is heated from room

a 0.1 m long mullite furnace tube is heated from room temperature 25 degrees celcius to 1000 degrees celcius. assuming

  Determine how much ice has melted to bring the temperature

(a) determine how much ice has melted to bring the temperature of the beverage to equilibrium with the ice/water. (b) Determine the final equilibrium temperature

  What is the velocity of the canoe when it hits the bottom

a water ride at cedar point involves a 200 lb canoe that slides down a 45 degree incline from an original elevation of

  Make a mohr circle representation of the stresses in the

the inner surface of a hollow cylinder internally pressurized to 100mpa experiences tangential and axial stresses of

  Determine the maximum exit velocity for this nozzle

Air enters an adiabatic nozzle at 5.18 MPa and 400K with a velocity of 20 m/s. The air exits at 2.00MPa. Determine the maximum exit velocity for this nozzle.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd