Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Consider a simply supported beam of lenght 50ft pinned on the left end at A and on a roller at the right end at B and subjected to a concentrated load of 20 kips at a distance of 20ft from A and a second concentrated load of 10kips 40 feet from A. The cross section of the beam is rectangular (b=4'' and h=8'').
a. Determine the shear and moment diagram.
b. Calculate the maximum normal stress on the top of the beam, on the bottom of the beam and indicate in terms of x its location.
c. Calculate the maximum shear and indicate in terms of x its location.
the flow profile is such that u=u(max)*(1-(r/R)^2) where u is the flow speed and r is the distance from the centre of the pipe in the radial direction. What is the shear stress on the pipe wall What is the shear force exerted by the oil on a 1m lo..
A 170 kg granite rock (ρ = 2700 kg/m 3 ) is dropped into a lake. A man dives in and tries to lift the rock. Determine how much force the man needs to apply to lift it from the bottom of the lake. Do you think he can do it?
Assume you are responsible for determining the maximum load that can be carried by a rectangular barge that is 8 m wide and 18 m long. The water line when the barge is empty is 3 m below the level of the cargo deck.
water flows from a lake as is shown in fig. p8.40 at a rate of 4.0 cfs. is the device inside the building a pump or a turbine? Explain and determine the horsepower of the device. neglect all minor losses and assume the friction factor is .025
A pre- engineering base line was run down a very steep hill.rather than measure horizontaily down hill with steel tape: surveyor measured the vertical angle with the theodolite and slope distance with 16m steel tape.
Knowing that portion AC of the rope lies in a plane parallel to the xy plane and that the magnitude of the tension T in the rope is 62 lb, determine the moment about O of the resultant force exerted on the pulley by the rope.
A pipe 1ft in diameter bends through an angle of 135 degrees. The velocity of flow of gasoline ( S = 0.8) is 20ft/s and the pressure is 10psig in the bend. What external force is required to hold the bend against the action of the gasoline
A multiple-piston hydraulic jack has two output pistons, each with an area of 250 cm^2. The input piston, whose area is 25 cm^2, is concerned to a lever that has a mechanical advantage of 9:1.
What power must the pump supply to the system to pump the oil from the lower reservoir to the upper reservoir at a rate 0.20 m^3/s. Sketch the HGL and the EGL for the system.
A concrete box girder bridge has the rectangular x-section. The box is prismatic and considered thin-walled. It span is L=48m and simply supported at points A,B,C and D. The supports are assume to be able to transfer tensile forces.
A cyclone is designed with an inlet width (W) of 12.0 cm and has four effective turns. The inlet gas velocity is 15.0 m/s and the particle density is 1.70 g/cm3. (a) Estimate the particle size that will be collected with 50 % efficiency.
what is the distiniction b/n point and non point sources of water pollution and thier varation with surface and ground water?
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd