Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A resistor, in series with a 138-µF capacitor, is connected to a 60-cycle source. If the voltage drop across the capacitor is 115 volts and the power taken by the circuit is 922 watts, calculate a) the circuit current, b) the ohmic value of the resistor, c) the line voltage, d) the circuit power factor
Design a 300W PFC BL-Zeta converter operating in DCM (Output Inductor) to maintain a DC link voltage of 100V with percentage ripple of 4%. The permitted ripple in the input side inductor and intermediate capacitor is given as 20%.
If a third attempt is made within 20 seconds, a waiting period of 20 seconds is required before additional attempts can be made to start the motor. While waiitng to make additional attempts to start the motor.
Two LTIC systems have impulse response functions given by h1(t)=(1-t)[u)t)-u(t-1)] and h2(t)=t[u(t+2)-u(t-2)].a) Carefully sketch the functions h1(t) and h2(t). b) Assume that the two systems are connected in parallel.
Construct a truth table for the state machine showing all possible states and the logic solution using J-K flip-flops. Construct K-maps for the J-K solutions, identify the minimum logic implementation (circle groups on K-maps), and write equations f..
Using synchronous Finite State Machine, design a sequential circuit that asserts a high output (Z) for exactly three clock pulses when an input button (B) is pushed (i.e. asserted). The circuit should stay idle with low output
Sketch the amplitude spectrum of a DTMF signal with finite duration. You should make this sketch by hand, using the Fourier transform expression obtained in part 1). What happens to the DTMF spectrum when T is "too small"
A signal source produces a 4 volt peak-to-peak sinusoid and has a source resistance of 100 ohms. We wish to drive a grounded 10 ohm load to at least 2 volts peak-to-peak with this source. The load cannot tolerate DC. Your amplifier should not burn..
Assume that the Fermi energy level for a particular material is 6.25eV and that the electrons in this material follow the Fermi-Dirac distribution function. Calculate the temperature at which there is a 1% probability that a state 0.30eV
A three-phase synchronous generator (Delta-connected) rated at 10KVA, 230 V, has a synchronous reactance of 1.2ohms per phase and an armature resistance of 0.5ohms per phase. (a) Draw the phasor diagram.
given a sequence x(n), where x(0) = 4, x(1) =3, x(2) = 2, and x(3) =1 with the last two data zero-padded as x(4) =0, and x(5) = 0, evaluate its DFT x(k)
A coil of wire contains 50 square turns, each one 5 cm long and 3 cm wide, and has a current of 30 A running through it. it is placed inside a magnetic field of 0.55 T at a 60 degree angle. what is the torque on the loop from the magnetic field
The voltage across the terminals of a certain circuit and the current entering into its (+) voltage terminal are given by: v = 4 + 12 Cos[377 t + 60 Degree] - 6 Cos[754 t - 30 Degree] i = 5 + 10 Cos[377 t + 45 Degree] + 2 Cos[754 t + 15 Degree] What ..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd