Another alternativeis an anodized metal exterior attached

Assignment Help Civil Engineering
Reference no: EM13540172

HJ Heinz Corporation is constructing a distribution facilityin Italy for products such as Heinz Ketchup, Jack Daniel's Sauces,HP steak sauce, and Lea & Perrins Worcestershire sauce. A15-year life is expected for the structure. The exterior of thebuilding is not yet selected. One alternative is to use theconcrete walls as the facade. This will require painting now andevery 5 years at a cost of $80,000 each time. Another alternativeis an anodized metal exterior attached to the concrete wall. Thiswill cost $200,000 now and require only minimal maintenance of $500every 3 years. A metal exterior is more attractive and will have amarket value of an estimated $25,000 more than concrete 15 yearsfrom now. Assume painting (concrete) or maintenance (metal) will be performed in the last year of ownership to promote selling the property. Use future worth analysis and i = 12% per yearto select the exterior finish.

Reference no: EM13540172

Questions Cloud

Suppose you are told that a process must achieve a : Suppose you are told that a process must achieve a 2.7 log removal of Giardia cysts.  What does that mean in terms of % remaining and % removal?
When do obnoxious odors appear : A dairy that processes about 250,000 lb of milk daily produces an average of 65,100 gpd of wastewater with a BOD of 1400 mg/L. The principal opearations are bottling milk and maing ice cream with limited produciton of cottage cheese.  What is the was..
Diameter circular concrete pile required to take a design : Using a safety factor of 2.00 and neglecting the pile dead weight, find the length of a 1' diameter circular concrete pile required to take a design load of 50 kips in a soil composed of two layers.
If the magnitude of cos t is less then write outan : The tangent function is defined as than (t)=sin(t)/cos(t). This expression can be evaluated to solve for the tangent as long as the magnitude of cos(t) is not too near to 0
Another alternativeis an anodized metal exterior attached : HJ Heinz Corporation is constructing a distribution facilityin Italy for products such as Heinz Ketchup, Jack Daniel's Sauces,HP steak sauce, and Lea & Perrins Worcestershire sauce. A15-year life is expected
What is the elevation at point 2 and the pressure at point 3 : A buried stock-water pipeline conveys water from a water source at Point 1, rises to pass up and over the peak of a hill (Point 2) before falling to Point 3 in the pipeline some
Select the lightest w 14 shape that will support a live load : Select the lightest W 14 shape that will support a live load of a 400 kips and a dead load of 75 kips for 20 feet tall column that is fixed at its top and bottom.
Find the component forces that the flange bolts must resist : Water at 20 degrees centrigrade in a 85 degree reducing bendis used in what is otherwise a continuous pipe. The systemoperating is 0.10 cubic meters per seconds
Write a paragraph explaining how the relaxation modulus : Write a paragraph explaining how the relaxation modulus of a plastic material measured in engineering practice. use a sketch.

Reviews

Write a Review

Civil Engineering Questions & Answers

  I want to know how to draw bending moment diagram for this

i want to know how to draw bending moment diagram for this shape and the value of the moment in critical sections

  Calculate the rate of change of water mass in the segment

The segment of river shown has a rectangular cross-section, with width 50 ft. The river bed is at angle theta=10 degrees from horizontal. The average velocity is 2 ft/s at the upstream end, and 3 ft/s at the downstream end.

  What is the magnitude of the force s if the angle is given

A pile resists the tension developed by three stay cables for a major tent (Membrane) Structure. Assuming no bending is desired in the pile (no resultant horizontal component), what is the magnitude of the force S if the angle \thetaS = 30 degrees

  How many grder hours will be required to accomplish the job

A motor grader will require 2 pases at 3 mph., 2 pases at 4 mph., and 2 passes at 5.5 mph. to accomplish the work How many grder hours will be required to accomplish this job if the job efficiency factor is 0.75.

  Determne the angular velocity at the instint theta

When theta=0 degrees , the assembly is held at rest, and the torsional spring is untwisted. If the assembly is released and falls downward, determne the angular velocity at the instint theta=90.

  Determine the length of the channel for the n

A trapezoidal channel of bottom width 25ft and side slope 1:2.5 carries a discharge of 450cfs with a normal depth of 3.5 ft. The elevations at the beginning and end of the channel are 685 and 650 ft, respectively.

  Circular and non-circular slip surfaces

The thickness of each layer is determined by the "last" ID number. Four student numbers are used as the example - Circular and non-circular slip surfaces should be considered

  How many hours should be taken an articulated wheel loader

How many hours should it take an articulated wheel loader equipped with a 4 yd3 bucket to load 3,000 yd3 of gravel from a stockpile into rail cars if the average haul distance is 300 feet one way

  Determine the average shear stress on the bolt surfaces

The top and bottom pull to the left with 10 kips each, the middle part 20 kips to the right. The bolts have a diameter 3/8 inch, determine the average shear stress on the bolt surfaces that are subjected to direct shear.

  What is effective vertical stress 12m below water surface

A river is 6 m deep. The riverbed material has a saturated unit weight of 19.5kN/m3. What is the effective vertical stress 12 m below the water surface

  Find stresses in ab and bc and the displacement at point c

A bar is under uniform axial loads. AB is 1 foot and has a area of .5 in^2 and BC is 1 foot and has an area of .3 in^2. AB has a 1000lb force putting it under tension and BC has a 500lb force putting it under compression

  Determine the required area of the members

The truss is to be constructed of members with equal cross-sectional areas and using a material with yield stress 700 MPa. The structure must be designed to support a mass (m) of 3400 kg with a factor of safety of 3.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd