A simple gear train with spur gears that contains a pinion

Assignment Help Mechanical Engineering
Reference no: EM13702445

A simple gear train with spur gears that contains a pinion, an idler, and a gear utilized in order to transmit 10 hp using a train ratio of 4.5:1. The pinion has 14 teeth and the idler has 30 teeth. The input shaft operates at 2000 rpm. The pressure angle is 25 degrees and the diametral pitch is 8 teeth/inch. Find the pitch diameters of the three gears. Also, compute the midrange and alternating components of the transmitted load on each gear.

Reference no: EM13702445

Questions Cloud

Fins for heat recovery : An inventor wants to increase the efficiency of wood burning stoves by reducing the energy lost through the exhaust stack. He proposes to accomplish this by attaching fins to the outer surface of the chimney, as shown schematically below.
Adiabatic turbine system to generate electricity : Steam is used in the following adiabatic turbine system to generate electricity; 15% of the mass flow from the first turbine is diverted for other use. How much work (in kJ/h) is generated by the first turbine which is 80% efficient?
Five pounds of propane have a volume : Five pounds of propane have a volume of 1 ft3 and a pressure of 600 psi. Determine the temperature (in °R) using each of the following methods.
Consider ideal regenerative rankine cycle for power plant : Consider the ideal regenerative Rankine cycle for a power plant (shown below), where there is no heat loss or pressure drops in the piping, the turbine and pumps are isentropic, the heat loss in open feed water heater (FWH) can be neglected, there ar..
A simple gear train with spur gears that contains a pinion : A simple gear train with spur gears that contains a pinion, an idler, and a gear utilized in order to transmit 10 hp using a train ratio of 4.5:1. The pinion has 14 teeth and the idler has 30 teeth. The input shaft operates at 2000 rpm. The pressure ..
Aerodynamic drag first exceed the rolling resistance : Consider a car having a frontal are of 2.0m^2 with a drag coefficient of 0.35. The mass of the car is 1250kg and the rolling resistance is 1.0% of the weight of the car. At what speed does the aerodynamic drag first exceed the rolling resistance.
A weak base that reacts with water according to the equation : Methylamine, CH3NH2, is a weak base that reacts with water according to the equation above. A student obtains a 50.0 mL sample of a methylamine solution and determines the pH of the solution to be 11.77.(a) Write the expression for the equilibr..
A 32.50-mg sample of naturally occurring elemental silicon : A 32.50-mg sample of naturally occurring elemental silicon was irradiated with neutrons in a nuclear reactor at a flux density of 2.75E-13 thermal neutrons per (cm^2 sec). The activity of 31-Si was determined at a remote site with a beta parti..
How many moles of oxygen gas have they inhaled : Air is 21% oxygen and 0.03% carbon dioxide at STP. Assume a person expands their lungs to breathe in 1.4L of air. How many moles of oxygen gas have they inhaled?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd