User Account

All Pages

A company has just negotiated a contract

Assignment Help Operation Management
Reference no: EM13922870

A company has just negotiated a contract to produce a part for another firm. In the process of manufacturing the part, the inside diameter of successive parts becomes smaller and smaller as the cut ting tool wears. However, the specs are so wide relative to machine capabilities that it is possible to set the diameter initially at a large value and let the process run for a while before replacing the cutting tool. The inside diameter decreases at an average rate of .001 cm per part, and the process has a standard deviation of .05 cm.
The variability is approximately normal. Assuming a three sigma buffer at each end, how frequently must the tool be replaced if the process specs are 3 cm and 3.5 cm?

Reference no: EM13922870

Questions Cloud

What would three-sigma control limits for the process be : What would three-sigma control limits for the process be? What alpha risk would they provide? What alpha risk would control limits of 4.14 and 4.86 provide?
What can you conclude about the data : Two additional observations have been taken. The first resulted in three defects, and the second had four defects. Using the set of 20 observations, perform run tests on the data. What can you conclude about the data?
How many units would this save in terms of the scrap : If the scrap rate for each step could be cut in half, how many units would this save in terms of the scrap allowance? If the scrap represents a cost of $ 10 per unit, how much is it costing the company per day for the original scrap rate?
Does it appear that the specs are being met : Suppose the process specs are 9.65 and 10.35 minutes. Based on the data given, does it appear that the specs are being met? If not, what should one look for?
A company has just negotiated a contract : A company has just negotiated a contract to produce a part for another firm. In the process of manufacturing the part, the inside diameter of successive parts becomes smaller and smaller as the cut ting tool wears
Use both types of run tests to analyze the daily : Use both types of run tests to analyze the daily expense voucher listed. Assume a median of $ 31.
Analyze the data in the problems listed : Analyze the data in the problems listed below using median and up/ down run tests with z = ± 2. a. Given the following run test results of process output, what do the results of the run tests suggest about the process?
Analyze the data using both median : For each of the accompanying control charts, analyze the data using both median and up/ down run tests with z = ± 1.96 limits. Are nonrandom variations present? Assume the centerline is the long termmedian.
The time needed for checking in at a hotel : The time needed for checking in at a hotel is to be investigated. Historically, the process has had a standard deviation equal to .146. The means of 39 samples of n = 14are

Reviews

Write a Review

Operation Management Questions & Answers

  Develop a proposal describing the potential it-enabled

Develop a proposal describing the potential IT-enabled competitive opportunities or threats O'Connell might be missing by not embracing IT. Be sure to include a Porter's Five Forces analysis and discuss which one of the three generic strategies O'..

  Define the differences between a project and a process

Contrast the differences between a project and a process. Explain why project management is often used to train future senior executives.

  Research the pros and cons of six software systems

Use the Internet, course materials and web resources to research the pros and cons of six software systems designed to perform these functions. Then, write a 5 - 7 page Software Recommendations Report that you will submit to the chief executive.

  Income is taxed at the corporate and shareholder levels

corporate income is taxed at the corporate and shareholder levels. Is there a way for Northwest Brands to avoid this double-income taxation?

  Typical manufacturing supervisors challenges

What are typical manufacturing supervisors' challenges, frequently created due to no fault of their own? Under newer, nontraditional manufacturing and operations methods, how can these problems reduce?

  Canned soft drinks and fruit drinks

The General Store at State University is an auxiliary bookstore located near the dormitories thatsells academic supplies, toiletries, sweatshirts and T-shirts, magazines, packaged food items, and canned soft drinks and fruit drinks.

  What are the functions of a manager

What are the functions of a manager? If you had to pick one as being the most important function, which would it be and why?

  Describe the culture of the united states of america

Using a minimum of three references, describe the culture of the United States of America including regards to observable artifacts, espoused values, and enacted values.

  How does toyotas philosophy of dealing with defects

How does Toyota's philosophy of dealing with defects, empowering employees, and developing capabilitiesimpact strategy execution?

  Lowest transportation costs for the system

Each of the locations has a demand potential of 300 units per week. Which location would yield the lowest transportation costs for the system?

  Raise morale and develop employees decision making skills

Mangers have the primary responsibility in most decision making process. However, if they involve employees, the decisions made can be more effective. Employees can help in any step of the decision making process, from problem identification through ..

  Create problems for inventory management?

Expansion of menu items create problems for inventory management?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd