What is the maximum weight that can be suspended on poll

Assignment Help Civil Engineering
Reference no: EM13317916

What is the maximum weight that can be suspended on a 16 Kg poll, 3/5 from the end? The maximum tension of the 30 degree guy-wire is 1500 N. Find the horizontal and vertical forces exerted on the poll by the hinge.

Reference no: EM13317916

Questions Cloud

Determine the resulting angular velocity of the wheel : A bolt located 50 mm fm he center of an automobile wheel is tightened by applying the couple for 0.10 s. Assuming that the wheel is free to rotate and is initially at rest, determine the resulting angular velocity of the wheel.
Explain why market outcomes are inefficient in the presence : Give two example of a negative externality and two examples of a positive externality Explain why market outcomes are inefficient in the presence of externalities.
What is the speed of the bullet before it impacted the block : A bullet of mass 25.0 g is fired into a wooden block of mass 2.200 kg that is initially at rest. what is the speed of the bullet before it impacted the block
Where to locate the mass center of the assembly : The two upper lengths of the welded Y-shaped assembly of uniform slender rods have a mass per unit length of 0.3 kg/m, while the lower length has a mass of 0.7 kg/m. Locate the mass center of the assembly. lenghts of all rods aew 30mm
What is the maximum weight that can be suspended on poll : What is the maximum weight that can be suspended on a 16 Kg poll, 3/5 from the end. The maximum tension of the 30 degree guy-wire is 1500 N. Find the horizontal and vertical forces exerted on the poll by the hinge.
What is min required heat transfer rate from heat source : A waste heat source is available at 400°C. A heat engine operates using heat from this source. It rejects heat to the surroundings at 38°C. The power from the engine runs an air conditioner to keep the air inside a building at 25°C
Find temperature at which air must leave heat exchanger : Gaseous oxygen (99% pure, molar basis) is to be produced at a rate of 350ft^3/hr in a Linde single column plant. The column operates at a pressure of 1 atm. Air leaves the compressor at a pressure of 10 atm.
How high did the ball roll before it momentarily stopped : A solid ball starts to roll up a hill with an initial velocity of 50m/s. The ball has a mass of 20 Kg with a 0.75 m radius. How high did the ball roll before it momentarily stopped
How far did the person climb on a frictionless vertical wall : A uniform ladder with a mass of 15 kg is placed on a frictionless vertical wall. An 80 kg person climbs up the ladder. If the coefficient of friction between the floor and the base of the ladder is 0.15, how far did the person climb

Reviews

Write a Review

Civil Engineering Questions & Answers

  Explain in detail different types of surveys

what are the main points which create necessity of new railway line? explain in detail different types of surveys conducted in railway work.

  Determine amount of coal used per day if heat of combustion

A coal fired power plant can be modeled as a heat engine. If the power output of the plant is 200 MW and the thermal efficiency is 42%, determine the amount of coal used per day if the heat of combustion from the coal is 24,000 kJ/kg.

  Sketch scs triangular and curvilinear uhs and mass curve

Sketch the SCS triangular and curvilinear UHs and the mass curve for a 100-mi^2 watershed which is 60% good condition meadow and 40% good cover forest land. The watershed consists of 70% soil group C and 30% soul group A.

  Calculating the ph of solution

A 1.50 L buffer solution is 0.250 M in HF and 0.250 M in NaF. Calculate the pH of the solution after the addition of 0.0500 moles of solid NaOH. Assume no volume change upon the addition of base. The Ka for HF is 3.5 x 10 -4 .

  Calculate earth gravitational force

Calculate Earth's gravitational force on the Shuttle astronauts while orbiting at an altitude of 220 miles (or 354 km) above Earth's surface.

  Calculate net present value

Set up life cycle diagram for both alternatives and calculate net present value (NPT) and annual cost for the life time.

  How many moles of water condense per cubic meter of feed gas

Suppose a sample of the 90 °C air is put in a closed variable-volume chamber containing a mirror, and the pressure is raised at constant temperature until a mist forms on the mirror. At what pressure would the mist form

  What are the interface design boundaries and issues

what are the interface design boundaries and issues for the design and installation of a new toilet for a building

  Calculate the film of oil thickness in centimeters

A flat plate weighing 220 N slides down a 15 degree incline with a velocity of 2.5 cm/sec. A thin film of oil with a viscosity of 1.29 N.sec/m^2 separates the plate from the ramp. if the plate is 50 cm by 75 cm, calculate the film thickness in cm.

  Determine the clearance between the tube and the cylinder

a 25-mm diameter steel cylinder 300-mm long falls, because of its own weight, at a uniform rate of 0.1 m/s inside a tube of slightly larger diameter. A castor-oil film of constant thickness is between the cylinder and the tube.

  Determine the magnitudes of the velocity of point o

The two pulleys are riveted together to form a single rigid unit, and each of the two cables is securely wrapped around its respective pulley. If point A on the hoisting cable has a velocity v=0.9 m/s,

  Determine time required for the bed to complete a full cycle

The velocity of the bed is limited to a maximum value of 150mm/s to the right and 300mm/s to the left; the acceleration is successively equal to 150mm/s^2 to the right, zero 150 mm/s^2 to the left, zero, etc.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd