What is the change in centimeters

Assignment Help Civil Engineering
Reference no: EM13540186

1.A result of a 7-day BOD test performed on a sample from anoligotrophic lake was 10 mg/L. The base 'e' BOD rate constant determined from previous studies was estimated to be 0.10d-1. Determine the ultimate BOD and 5-day BOD of the sample taken from the lake.

2.The evaporation rate from the surface of a 3,650-acre lake is 100 acre-ft/day. Estimate the depth change in the lake in feet during a 1-year period if the net inflow to the lake is 25 cfs. Is the depth increasing or decreasing? What is the change in centimeters?

Reference no: EM13540186

Questions Cloud

Imagine that a relativistic train travels past your lecture : Imagine that a relativistic train travels past your lecture room at a speed of 0.887 c. The passengers of the train claim that when they measure the length of the train using standard meter bars found on the train, the length comes out to be 85.8 ..
Find the moment of inertia around the x-axis and y-axis : Using a unit analysis, calculate the value of the K term in the rational method equation (Q = K C I A) in English and SI respectively.
What rate must heat be supplied to this engine : A completely reversible heat engine operates with a source at 1500 R and a sink at 500 R. At what rate must heat be supplied to this engine, in Btu/h, for it to produce 5 hp of power?
Determine the solids retention time : Using the following assumptions, determine the solids retentiontime, the cell wastage flow rate, and the return sludge flow ratefor the Jambalaya shrimp processing plant WWTP.
What is the change in centimeters : The evaporation rate from the surface of a 3,650-acre lake is 100 acre-ft/day. Estimate the depth change in the lake in feet during a 1-year period if the net inflow to the lake is 25 cfs. Is the depth increasing or decreasing? What is the change in ..
Determine the combined amounts of water evaporated : Helium (Hrom an intie) at a rate of 1.5 lbm/s is compressed inan adibatic compressor from an intial condition of 70 F, 14.7 Psiato final condtion of 1070 F, 147 Psia. Determine:
The detention time should be 60 seconds with a velocity : A circular rapid-mix basin with stator blades is to be designed totreat 2.0 million gallons of water per day. The detention times hould be 60 seconds with a velocity gradient of 900s-1
At what height in the resevoirmust the water level be kept : Water at 20 Degree C is pumped at a constant rate of 9m^3/h from a large resevoir resting on the floor to the open top of a anexperimental absorption tower.
Find e in terms of b and h to have one type of normal stress : For arectangular section (b(width) x h(thickness) that is subjected to aforce P that is applied at an eccentricity (e) measured from thecenter of area of the rectangle in the h(thickness)direction

Reviews

Write a Review

Civil Engineering Questions & Answers

  Design temperature and residence time have been established

Assume that the design temperature and residence time have been established as 1300 degrees F and 0.6 seconds, respectively. The type of burner used in the process requires outside air at a mass ratio of 12:1 (air to fuel gas).

  Estimate the daily emissions of particles from a solid-waste

The incinerator burns 50 tonnes per day (1 tonne= 1 metric ton= 1000kg) and exhausts gases in a ratio of 20kg of gases per kg of feed. Assume the gases exit at 200*C and 1atm.

  Calculate the terminal settling velocity in standard air

Assuming Stokes behavior, calculate the terminal settling velocity in standard air for the following particles: (a). diameter = 10 micrometers, specific gravity =1.2; and (b) diameter = 4 micrometers, specific gravity = 2.0.

  Find the conjugate depth to an initial flow depth

A trapezoidal channel having bottom width of 8 m and side slopes of 1 : 1, carries a discharge of 80 m^3/s. Find the conjugate depth to an initial flow depth of 0.75 m before the jump.

  Problem 1 solve the following three questions of the beam

problem 1. solve the following three questions of the beam abc. note that a is a roller support b is a pin connection

  How long would it be before company could sell the property

A multinational engineering consulting firm that wants to provide resort accommodations to certain clients is considering the purchase of a three-bedroom lodge in upper Montana that will cost $250,000.

  Write the vector expression for velocity of a as measured

The air transport B is flying with a constant speed of 480 mi/hr in a horizontal arc of 9-mi radius. When B reaches the position, aircraft A, flying south-west at a constant speed of 360 mi/hr

  Freeway capacity and los

A four-lane freeway (two lanes in each direction) is on mountainous terrain with 11ft lanes, a 5ft right-side shoulder, interchange spacing of one every 10 miles, and a 60mph base free-flow speed.

  What load factor is required to break even using

A Chicago-based international air carrier plans to purchase a jumbo-class aircraft (Airbus A-340-600 or B777-200IGW) to serve the Chicago-London city pair

  Determine what is the equation for average vehicle delay

What is the equation for average vehicle delay Is it averge queue over arrivals Average queue over average arrivals

  Find the temperature stress produced

A rod of steel is 20 m long at a temperature of 200C. find the free expansion of the rod when the temperature is raised to 650C. Find the temperature stress produced

  Determine the average velocity for the portion of the flow

An in-compressible fluid flows horizontally in the x-y plane with a velocity given by u = 33 (y/h)^1/2 , where y and h are in meters and h is a constant. Determine the average velocity for the portion of the flow between y = 0 and y =h.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd