What is the amplitude of the force transmitted to building

Assignment Help Mechanical Engineering
Reference no: EM13711484

Consider a model of a building whose base moves as a result of an earthquake. The building can be modeled as a single-degree-of-freedom spring-mass system where the building mass is lumped on top of two beams used to model the walls of the building. The ground motion has an amplitude of 0.1 m and a frequency of 7.5 rad/s. The building mass is 105 kg and the stiffness in bending of each wall is 3.519*10^6N/m.

a) Write down the equation of motion of the mass, which represents the building.

b) Compute the natural frequency

c) Compute the amplitude X of the steady-state response.

d) Does the amplitude seem large? Comment on your answer.

e) What is the amplitude of the force transmitted to the building?

Reference no: EM13711484

Questions Cloud

Find the magnitude of reactions at a and the tension in rope : A block is L = 1 [m] long and h = 0.5 [m] tall and weighs 50 [N]. The box is allowed to rotate about point A. A rope is attached to the upper left corner. This rope makes a θ=40° angle from the horizon. A horizontal force of 30 [N] is applied at th..
Converted at constant pressure to saturated steam : Liquid water is fed to a boiler at 24ºC and 10 bar is converted at constant pressure to saturated steam. Use the steam tables to calculate H (kJ/kg) for this process, and then calculate the heat input required to produce 15,000 m3/h of steam at the e..
Nozzle to keep it from moving horizontally backwards : A fireman is using a 10-cm inside-diameter fire hose is trying extinguish a fire. He is aiming the hose at 45° with respect to the horizontal and the water lands 30 m from the fire fighter. On the end of the fire hose is a nozzle. The inside diamete..
What is the discharge velocity : Air enters an adiabatic nozzle at 3 atm pressure and 100 F and emerges at 1 atm and 30 F. The inlet velocity is negligible. What is the discharge velocity?
What is the amplitude of the force transmitted to building : Consider a model of a building whose base moves as a result of an earthquake. The building can be modeled as a single-degree-of-freedom spring-mass system where the building mass is lumped on top of two beams used to model the walls of the building.
Changes in kinetic and potential energies is zero : Ten cubic feet of air is cooled at a constant pressure of 80 psi. The initial temperature is 180 0F and the final temperature is 100 0F. Assume air is an ideal gas, Cp = 0.241 Btu/lb 0R and Cv = 0.173 Btu/lb 0R and R = 1545 lbf/lbmol 0R, M = 28.97 lb..
Solid glass-polymer reinforced composite rod : Solid glass-polymer reinforced composite rod (diameter = 100 mm) is simultaneously torqued clockwise (T = 1,000 Nm) and given a tensile load (P = 0). Determine shear strain. Determine extensional strains in n and t directions.
Calculate the maximum shear stress for each stress element : A cantilever beam with a 1 in diameter is loaded at the tip with a transverse force of 1000 lb. Figure 2.1 below shows the beam configuration and cross-section with points A at the top, point B at the center and point C at the midpoint between A and ..
Heat exchanger tubes have to be shorter txceed : In a Modified Rankine Cycle used in a power plant in Wichita, KS, a Shell and Heat Exchanger needs to be installed. Water from the turbine at 90 C is cooled to 80 C in a shell-tube HX using 150 kg/s of raw water from Power Plant Lake.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd