What are the work and heat transfer for this process

Assignment Help Mechanical Engineering
Reference no: EM13704734

A 100L rigid tank contains nitrogen (N2) at 900K, 3 MPa. The tank is now coole to 100K. What are the work and heat transfer for this process?

Reference no: EM13704734

Questions Cloud

A worker-machine operation was found to involve 3.5 : A worker-machine operation was found to involve 3.5 minutes of machine time per cycle in the course of 40 cycles of stopwatch study. The worker's time averaged 2.7 minutes per cycle
What is the fuel to air ratio and air flow rate : A 380 cc single-cylinder two-stroke motorcycle engine is operating at 5500 rpm. The engine has a bore of 82 mm and a stroke of 72 mm. Performance testing gives a bmep od 6.81 bar, bsfc of 0.49 kg/kW hr, and delivery ratio of 0.748. a) What is the fue..
Steel alloys corresponding to their carbon content : Using the standard Fe-C phase diagram, draw a vertical line for each of the following steel alloys corresponding to their carbon content: AISI 1018, AISI 1045, AISI 1095, AISI 4140. Draw a point on the line for each alloy at 800oC and 425oC and descr..
Discuss the role of reward systems in organizational change : Discuss the role of reward systems in organizational change. Specifically, identify where reward systems work and where they undermine the organizational change process. If you have no experience in the work field please use the classroom setti..
What are the work and heat transfer for this process : A 100L rigid tank contains nitrogen (N2) at 900K, 3 MPa. The tank is now coole to 100K. What are the work and heat transfer for this process?
What are the heat transfer and work in the process : Two kg water at 120C with a quality of 25% has its temperature raised 20C in a constant volume process. What are the heat transfer and work in the process?
Find expression for the isothermal compressibility : Find expression for the isothermal compressibility and coefficient of thermal expansion for a fluid that is described by the van der waals equation of state. Expression should be in term of measurable properties.
Hypothesis testing : Hypothesis testing is a well-structured process that consists of several logical steps, and it aims at refining a business decision.Hypothesis testing is a quite common technique used by researchers. With regard to hypothesis testing, answer the ..
Determine the amount of oxygen in the tank : The pressure gauge on a 2.5-m^3 oxygen tank reads 500 kPa. Determine the amount of oxygen in the tank if the temperature is 28 degrees C and the atmospheric pressure is 97 kPa.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd