User Account

All Pages

The average speed in the discharge pipe is 3 ms if the pump

Assignment Help Mechanical Engineering
Reference no: EM13630334

A pump draws water from a reservoir through a 150 mm diameter suction pipe and delivers it to a 75 mm diameter discharging pipe. The end of the suction pipe is 2 m below the free surface of the reservoir. The pressure gage on the discharge pipe (2 m above the reservoir surface) reads 170 kPa. The average speed in the discharge pipe is 3 m/s. If the pump efficiency is 75 %, determine the power required to drive it.

 

Reference no: EM13630334

Questions Cloud

Water at 25 degrees c enters a heat exchanger at 01 kgs and : water at 25 degrees c enters a heat exchanger at 0.1 kgs and exits at 50 degrees c. kerosene enters the other side of
An electron is released from rest at the point midway : two stationary positive point charges charge 1 of magnitude 3.10nc and charge 2 of magnitude 1.75nc are separated
What is the current potential difference and dissipated : what is the current potential difference and dissipated power for each when they are connected in
A steam turbine operating at steady state has water : a steam turbine operating at steady state has water entering at 3mpa 500 degrees c and velocity of 10ms the water exits
The average speed in the discharge pipe is 3 ms if the pump : a pump draws water from a reservoir through a 150 mm diameter suction pipe and delivers it to a 75 mm diameter
A nitrogen line 300 k and 05 mpa shown in the figure is : a nitrogen line 300 k and 0.5 mpa shown in the figure is connected to a turbine that exhausts to a closed initially
At a certain instant a valve is opened and mass flows from : compressed air is stored in a pressure bottle with a volume of 10 ft3 at 3000 psia and 140 f. at a certain instant a
What are individual cutting tool with a number of cutting : what are individual cutting tool with a number of cutting edges. they are useally held on the tool shank with various
The cylinder with a friction-less piston of 2-kg mass and a : the cylinder with a friction-less piston of 2-kg mass and a radius of 5 cm initially at 1 liter in volume and is filled

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the yield strength

If the critical resolved shear stress is 10 MPa, what is the yield strength?

  Determine the required velocity

Coal discharged from a dump truck with an initial velocity (v)= 1.8m/s at 50 degrees falls on conveyor belt B. Determine the required velocity v(B) of the belt if the relative velocity with which the coal hits the belt is to be vertical.

  Heat is conducted along a circuit board that has a copper

heat is conducted along a circuit board that has a copper layer on one side. the circuit board is 15 cm long and 15 cm

  A reheat cycle operates with initial steam conditions of

a reheat cycle operates with initial steam conditions of 1500 psia and 1000 degrees fahrenheit at the inlet to the

  Calculate the thermal efficiency of the cycle neglect the

superheated steam at 10 mpa and 480c leaves the steam generator of a vapor power plant. the power plant is operated by

  A 9 m3 tank has two sections separated by a membrane both

a 9 m3 tank has two sections separated by a membrane both of which contain nitrogen gas. the nitrogen in section a has

  A linear bearing supports a load w has a contact area a

a linear bearing supports a load w has a contact area a and travels at a maximum velocity v. what expression will be

  Plot contours of u-velocity and v-velocity

The velocity profiles at locations x=0.1, 0.30 and 0.5. Plot contours of u-velocity and v-velocity. How many iterations did it take to get your solution?

  A piston cylinder device initially contains 5kg of water at

a piston cylinder device initially contains 5kg of water at saturated liquid state1. it undergoes a process in which it

  Draw and label the t-s diagram for the ideal rankine cycle

water is the working fluid in an ideal rankine cycle. superheated vapor enters the turbine at 8 mpa 450 degc. the

  Heat transfer between the compressor and its surroundings

refrigerant 134a enters a compressor operating at steady state as saturated vapor at -4 degc and exits at a pressure of

  If the copper sphere is initially at 1000k perform an

a 1-in diameter pure copper sphere is suspended in a room where the walls and air are all at 300k. the natural

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd