### Show a diagram of connections as an autotransformer

Assignment Help Electrical Engineering
##### Reference no: EM13281494

A 480-120 volt, 5kVA, 2-winding transformer is to be used as an autotransformer to supply a 480-volt circuit from a 600-volt source. When tested as a 2-winding transformer at rated load, 0.8 pf lagging, its efficiency is 0.965.

Show a diagram of connections as an autotransformer. On the diagram show polarities and current directions.

### Previous Q& A

#### What is brown unlevered beta

What is the WACC before and after the capital structure change. Should Brown increase their debt to 40%?

#### Identify possible actions to help boost profitability

Assume a large physician group practice has a low return on equity (ROE). How could Du Pont analysis be used to identify possible actions to help boost profitability?

#### Design a full wave bridge rectifier as a dc power supply

Design a full wave (Bridge) rectifier as a dc power supply that provides a peak dc output voltage of 15V on which maxiumum of 5% ripple is allowed. The rectifier feeds a load of 200Ω. The rectifier is fed from the line voltage (120V rms, 60 Hz) th..

#### Genentech reported net income in 2001 equals

In 2001, Genentech had 535.3 million average common shares outstanding, actual shares outstanding at year-end of 528.3 million and reported earnings per share of \$.28. Genentech's reported net income in 2001 equals

#### What will its dividend payout ratio be

If the company follows the residual dividend model, how much income must it earn, and what will its dividend payout ratio be?

#### What is the highest elevation that can be achieved

We are imaging a field for NASA from a satellite. The field has vertical (sinusoidal) stripes that repeat at a rate of 1 stripe per meter. Our satellite has a CCD sensor (camera) that is 1 cm x 1 cm. This sensor has 1000x1000 pixels.

#### Explain mole ratio of tin to oxygen be too high

Spattering does occur and some of the sample is lost onto the laboratory bench. Will the reported mole ratio of tin to oxygen be too high, too low, or unaffected. Explain.

#### Determine the set is linearly dependent or not

Determine if the set is linearly dependent or linearly independent

#### When i went through the checkout process

When I went through the checkout process, It said that I would have access to the "ebook" version and because I need the access right away I ordered it however, I don't see where or how I get the ebook version can you please direct me to it?

#### Evaluate the kinetic energy of the ejected electron

The work function (i.e binding energy) W, of cesium of metal is 3.43 x 10^-19 J. Calculate the kinetic energy of the ejected electron if light of frequency 1.00 x 10^15 s-1 is used for irradiating the metal.

### Similar Q& A

#### Find the average power dissipated in the soldering iron

The heating element in a soldering iron has a resistance of 30-ohm. Find the average power dissipated in the soldering iron if it is connected to a voltage source of 117 V rms.

#### Design an amplifier capable of providing the specified gain

Design an amplifier capable of providing the specified gain over a frequency range of 20 Hz to 10Khz under the following conditions. Input source is 2700ohms resistive, and the output load impedance is 32ohms resistive.

#### Calculate the spacing between the electrons on a lattice

An electron beam coming from an electron gun consists of electrons that are uniformly distributed within a cylindrical region of space having a radius a = 1 [mm]. The axis of the cylinder is along the z axis, and the electrons are moving

#### Find average power loss in line before and after load added

The power factor of the added load is to be adjusted so that the overall power factor of the factory is 0.96 lagging. The factory is fed from a line having an impedance of 0.02 + j0.16 O. The voltage at the factory is maintained at 480 V(rms).

#### Develop a coherent demodulation for the modulated signal

Use a modulation index of 50 percent and a sampling rate of 160 kHz. In this project, develop a coherent demodulation for the modulated signal. Assume there is no channel error.

#### Determine the position x and the tension in the cord

Determine the position x and the tension in the cord that is required for equilibrium. The cord passes through the smooth ring at B and has an unstretched length of 6ft and stiffness of k = 50lb/ft.

#### How can one go about to decode a message from a wav file

how can one go about to decode a message from a wav file. the wave contain a coded message in form numbers. which is represented in the wave in form of tones

#### Design an interface for the geared dc motor

An alarm is powered by 120 VAC, and the on/off state of the alarm is controlled by an EM relay. Design the interface between a computer output port and the EM relay. The dropout voltage is 3.5 V, and the coil current needs at least 100 mA.

#### Compute the volt f the optimum threshold

a digital signal represented by a binary voltage +5.55 and -4.5V , is transmitted over an AWGN channel with noise standard dev 1.12 V.Compute the volt. f the optimum thresholdwhen the priori probabilities of the binary source

#### What resistance must be connected in series with heater rate

What resistance must be connected in series with a heater rated at 150mA with hot resistance of 320 ohm in order to operate it safely from a 117-V source. What power rating must this resistor have

#### What electrical code is universally used in the united state

Identify the type of cable that is permitted in single- and multifamily dwelling units but that cannot be used underground, nor in buildings that are more than three stories above grade, nor in commercial garages, motion picture studios, theaters,..

#### Is the energy of the signal finite and why

f(t) = A[u(t) + u(-t/2-5)-1], where u(t) is the unit step function. Is the energy of this signal finite? Why or why not. If it exists, find the energy of this si