Obtain timing diagram for positive-edge-triggered flip flop

Assignment Help Electrical Engineering
Reference no: EM13270750

Obtain a timing diagram for a positive-edge-triggered JK master-slave flip-flop during four clock pulses. Show the timing diagrams for C, J, K, Q and Q'. Assume that before the first pulse: output Q is equal to 1, J=0 and K=1. Then, after the second clock pulse, J=1 and K=0. After the third clock pulse J=1 and K=1.

Reference no: EM13270750

Questions Cloud

Explain the freezing point decreases of hbr : When 1 mol of HF is added to 1kg of water, the freezing point decreases by 1.9 C, but when 1 mol of HBr is added, the freezing point decreases by 3.7 C. Which is more highly separated into ions, HF or HBr
Explain difference in a zener diode and pn junction diode : A pn junction diode is reverse-biased when 5V of an external voltage is applied to the p-side of the diode while the n-side is grounded If two pn junction diode are connected in series pointing each other, at least 1.4 V must be applied to turn bo..
Mri scan calibrated to detect preferences for risk and retur : Write a half-page pamphlet in everyday language that could be used to educate your client about port olio formation. It was found, from the results of a special MRI scan calibrated to detect preferences for risk and return,
Explain begins as a liquid that the specific heat of water : How much energy (heat) is required to convert 248 g of water from 0oC to 154oC? Assume that the water begins as a liquid, that the specific heat of water is 4.184 J/g.oC over the entire liquid range, that the specific heat of steam is 1.99 J/g.oC,
Obtain timing diagram for positive-edge-triggered flip flop : Obtain a timing diagram for a positive-edge-triggered JK master-slave flip-flop during four clock pulses. Show the timing diagrams for C, J, K, Q and Q'. Assume that before the first pulse: output Q is equal to 1, J=0 and K=1.
Explain the freezing point decreases : When 1 mol of HF is added to 1kg of water, the freezing point decreases by 1.9 C, but when 1 mol of HBr is added, the freezing point decreases by 3.7 C. Which is more highly separated into ions, HF or HBr
Effect of the whistleblowers actions : Details of the issue that the whistleblower reported and the effect of the whistleblower's actions on both the whistleblower himself and the company.
How many grams of solute are required to prepare solution : How many grams of solute are needed to prepare the following solutions? 1. 135.0mL of 22 % (w/v) glucose (C6H12O6) 2. 60mL of 4.6 % (w/v) (KCl)
What is the final pressure inside the container : A closed container with volume of 7.80 L holds 9.6 g of liquid helium at 3.00 K, What is the final pressure inside the container

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find max thermoelectric generation efficiency for any temp

A newly proposed thermoelectric generation material is the skutterudite family, such as FeAs3 or CoAs3. Assuming this new material has a Seebeck coefficient S = 35 V/K (microvolts per degree Kelvin), the electronic conductivity =1x104 (Ohm-cm)-1

  Find magnitudes of reflection and transmission coefficient

A uniform plane wave propagates from one dielectric into another at normal incidence. Find the ratio of the dielectric constants such that the magnitudes of the reflection and transmission coefficients are both equal to 0.5.

  Describe when does computer a retransmit the message

The messages being sent are 2 milliseconds long. Computer A starts sending a message on the bus; 250 microseconds later, Computer B starts to send a message, and 250 microseconds after that, Computer C starts to send a message.

  Determine the signal voltage at the collector

A 50 mV signal is applied to the base of a properly biased transistor with r =10-ohm and Rc=560-ohm. Determine the signal voltage at the collector.

  What is the rms value of the voltage waveform

a certain ideal voltage generator is characterized as v(t) = 40 sin 377 t . If this generator is measured with a DC voltmeter, the instrument reads 12 volts, what is the rms value of this voltage waveform

  Determine how fast must hit the ball to land at the base

in the bottom of the 9th inning, the bases are loaded and the braves are down by three runs. chipper johns steps to the plate. twice he swings and misses. The crowd heads for the exits. the next pitch is a fast ball down the middle.

  Find the density for germanium

Find the density for germanium (Ge) semiconductor atoms give that its lattice constant a-5.66Å (Angstrom) and atomic weight is 72.59 g/mole.

  Non-feedback- four-character combinations

Assuming no feedback to the adversary until each attempt has been completed, what is the expected time to discover the correct password?

  Design the circuit with input p and output f

Design a circuit with input p and output f that will output f = 1 if the past three inputs (not including the current input), formed either 010 or 000. Otherwise, f = 0. Note: This is a Moore-type finite-state machine.

  What should the gain of the amplifier be to have 10 dbm

The desired signal at the output of the amplifier is 10 dBm, and the signal level applied to the fiber connector at the head end is 10 dBm. What should the gain of the amplifier be to have 10 dBm at the output of the neighborhood amplifier

  Explain the two possible frequencies

What are the two possible frequencies to which the local oscillator could be set? What bandwidth should the 10.7 MHz IF amplifier have?

  How to compare the results with the ones for analog filter

Compare these results with the ones for analog filter and comment. Notice that the frequency response of digital filter has linear normalized frequency in [0,f] when the bode plot gives a logarithmic frequency axis of different range.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd