Name a few linear ics besides the op amp

Assignment Help Electrical Engineering
Reference no: EM131282404

1. With zero input voltage to an ideal op amp, why is there exactly zero output voltage?

2. Name a few linear ICs besides the op amp.

3. What condition is needed for an LM741 to produce maximum voltage gain?

Reference no: EM131282404

Questions Cloud

What are strengths and weaknesses of carlos ghosns approach : What are the strengths and weaknesses of Carlos Ghosn's approach to change leadership at Nissan? To what extent has he succeeded in mobilizing adaptive behavior on the part of employees?
Trade off between backward compatibility and performance : Discuss the conditions under which pre-market standardization is more likely to emerge as an equilibrium than a standards war.
Design a networking scheme : COM524: Data Communications and Networks - Design a networking scheme you have only been allocated 1 network address which is 192.168.0.X. Allow for 50 hosts on the Paris Router and 25 on the Warsaw Router.
Why is a 741c thought of as a dc or low-frequency amplifier : Draw a noninverting op amp and derive the formula for voltage gain.
Name a few linear ics besides the op amp : With zero input voltage to an ideal op amp, why is there exactly zero output voltage?
Compare two polar business models for market intermediation : Why do buyers and sellers sometimes prefer to trade via a dealer rather than in a decentralized way?- Taking the viewpoint of an intermediary, compare two polar business models for market intermediation.
What are some possible disadvantages of using the 318 : The LM318 is a much faster op amp than the LM741C. In what applications might the 318 be preferred to the 741C? What are some possible disadvantages of using the 318?
Describe the sorting role of the prices set : Describe the sorting role of the prices set by intermediaries in matching markets.-  How do intermediaries set the price structure on two-sided platforms?
How do you seperate compassion and caring for an employee : How do you seperate compassion and caring for an employee with being the employee's boss? When does free speech become insubordination? Do you think it's realistic that all employees can be treated equally?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Calculate the rotor copper loss

A 3-phase, 400 V, 6-pole, 50 Hz induction motor develops mechanical power of 20 kW at 985 rpm.

  What is the maximum range of coverage

What is the minimum Eb/Ieff (bit energy over effective noise energy) to yield P(e)

  A test on an 80 w fluorescent lamp circuit gave the ff

a test on an 80 w fluorescent lamp circuit gave the ff. results when connected to a 50 hz mains supply. calculate the

  Estimate the resistance of the human body using the figures

A stun gun or TASER is designed to put out a few seconds worth of electric pulses that impress a voltage of about 1200 V across the human body. This results in an average current of approximately 3 mA into a human body.

  A uniform probability distribution

A uniform probability distribution

  Obtain an expression for the spectrum of an fm signal

Obtain an expression for the spectrum of an FM signal with single-tone modulation where the carrier amplitude is Ac, the carrier frequency is Fc, the message frequency is fm and the modulation index is B (beta).

  Effective reverse saturation current

1. The MOSFET circuit in the figure below is used to perform a DC Sweep analysis of the transistor. Given the results shown, determine the effective reverse saturation current for this transistor in its diode mode of operation.

  Find the maximum value of k for which the system is stable

Find the maximum value of K for which the system is stable

  Transmitting two different signals with two different wave

If we use a single mode fiber with 17 ps/nm/km dispersion for transmitting two different signals with two different wavelengths - 1550 and 1560 nm respectively -, what is the time delay between those two signals after 100 km?

  What will be the new frequency and the load sharing

In part (b) which should be the set point of G2 for the system frequency to be 50 Hz? What would be the load sharing now?

  What is the ratio fo the amplitudes of the back emf

Assume we have a toroidal coil with a rectangular cross section, with an inner radius 1 cm, an outer radius 2 cm, a height of 1 cm and 1000 turns. The coil is connected to a resistor of 500 ohms. An AC current I(t) = Io cos(wt)

  The given image compute what you would expect for vce

If β=100, and Vin=0.2cos(2πf*t)+2 V where f=100 Hz, compute what you would expect for Vce. Assume Vcc=5V, Rb=20 kΩ, Rc=200 Ω from the given image.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd