Magnitude of the cars acceleration during the turn

Assignment Help Mechanical Engineering
Reference no: EM13703850

The car travels at a constant speed of 25 m/s makes a turn on a semi-circular curve. If it takes 20s to make the semi-circular turn, determine the magnitude of the car’s acceleration during the turn.

Reference no: EM13703850

Questions Cloud

Atmospheric pressure and temperature fills a sealed : Water at standard atmospheric pressure and temperature fills a sealed, rigid container. If the temperature of the water is increased by 50°C, what is the pressure? Assume that the coefficients of compressibility and thermal expansion are constant
Mini submarine to explore a deep part of the mariana trench : You want to use a mini submarine to explore a deep part of the Mariana Trench in the North Pacific Ocean, which is 10,924 meters (35,840 ft or 6.8 miles) below sea level. A salesperson at Hydro subs, Inc., offers to sell you a mini sub that can withs..
A cutting tool on a lathe applies a tangential force : A cutting tool on a lathe applies a tangential force of 3.5 kN when it is machining a bar 150 mm in diameter. If the lath is turning at 100 rpm, what power is being supplied to the bar?
Micro fluidics is in the area of electro kinetic separations : An important application of micro fluidics is in the area of electro kinetic separations, in which an electric field is applied along the length of a micro channel to generate differential velocities for various components (molecules, nano particles,..
Magnitude of the cars acceleration during the turn : The car travels at a constant speed of 25 m/s makes a turn on a semi-circular curve. If it takes 20s to make the semi-circular turn, determine the magnitude of the car’s acceleration during the turn.
Pilot in an airplane flying horizontally with constant speed : A pilot in an airplane flying horizontally with constant speed of v = 480 km/hour at an elevation of h=610 m above a level plain wishes to bomb a target B on the ground as shown below. At what angle below the horizontal should he see the target at th..
Brass rod is stress-free at room temperature : A brass rod is stress-free at room temperature (20 degrees Celsius). It is then heated up but prevented from lengthening at its ends by external forces. At what temperature does the stress in the rod reach 172 MPa? Assume the modulus of elasticity is..
Contains nitrogen gas with an absolute pressure : A rigid tank contains nitrogen gas with an absolute pressure of 113.1 kPa. A vacuum pressure gage connected to the tank reads -14.2 kPa-vacuum. What is the local atmospheric pressure (in kPa)?
Designing optimum straight-line fourbar linkages : For an assembly line, you need to design a linkage that moves a point P in approximately a straight line over a distance of 24” in one second. It is also specified that P must return from the endpoint back to the starting point in five seconds, givin..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd