Indicate the type and the nature of the actuators

Assignment Help Mechanical Engineering
Reference no: EM131393263

You are a control engineer who has been assigned the task of designing and instrumenting a control system. In the final project report you will have to describe the steps of establishing the design/performance specifications for the system, selecting and sizing sensors, transducers, actuators, drive systems, controllers, signal conditioning and interface hardware, and software for the instrumentation and component integration of this system. Keeping this in mind, write a project proposal giving the following information:

1. Select a process (plant) as the system to be developed. Describe the plant indicating the purpose of the plant, how the plant operates, what is the system boundary (physical or imaginary), what are important inputs (e.g., voltages, torques, heat transfer rates, flow rates), response variables (e.g., displacements, velocities, temperatures, pressures, currents, voltages), and what are important plant parameters (e.g., mass, stiffness, resistance, inductance, conductivity, fluid capacity). You may use sketches.

2. Indicate the performance requirements (or, operating specifications) for the plant (i.e., how the plant should behave under control). You may use any available information on such requirements as accuracy, resolution, speed, linearity, stability, and operating bandwidth.

3. Give any constraints related to cost, size, weight, environment (e.g., operating temperature, humidity, dust-free or clean room conditions, lighting, wash-down needs), etc.

4. Indicate the type and the nature of the sensors and transducers present in the plant and what additional sensors and transducers might be needed for properly operating and controlling the system.

5. Indicate the type and the nature of the actuators and drive systems present in the plant and which of these actuators have to be controlled. If you need to add new actuators (including control actuators) and drive systems, indicate such requirements in sufficient detail.

6. Mention what types of signal modification and interfacing hardware would be needed (i.e., filters, amplifiers, modulators, demodulators, ADC, DAC, and other data acquisition and control needs). Describe the purpose of these devices. Indicate any software (e.g., driver software) that may be needed along with this hardware.

7. Indicate the nature and operation of the controllers in the system. State whether these controllers are adequate for your system. If you intend to add new controllers briefly give their nature, characteristics, objectives, etc. (e.g., analog, digital, linear, nonlinear, hardware, software, control bandwidth).

8. Describe how the users and/or operators interact with the system, and the nature of the user interface requirements (e.g., graphic user interface or GUI).
The following plants/systems may be considered:

1. A hybrid electric vehicle

2. A household robot

3. A smart camera

4. A smart airbag system for an automobile

5. Rover mobile robot for Mars exploration, developed by NASA.

6. An automated guided vehicle (AGV) for a manufacturing plant

7. A flight simulator

8. A hard disk drive for a personal computer

9. A packaging and labeling system for a grocery item

10. A vibration testing system (electrodynamic or hydraulic)

11. An active orthotic device to be worn by a person to assist a disabled or weak hand (which has some sensation, but not fully functional)

Reference no: EM131393263

Questions Cloud

Describe the center and spread of the distribution : Create a stem-and-leaf display for these data, using split stems.- Describe the shape of the distribution.- Describe the center and spread of this distribution.
How the office setting might be configured : In addition, explain the types of additional marketing research you would recommend the organization conduct given this scenario. How the office setting might be configured
Find a value for continuous torque : Determine a value for continuous torque and a corresponding value for operating speed on which a selection of a motor and a drive unit can be made.
Summarize the center with a mean : For which of the variables depicted in the histograms would you most strenuously insist on using an IQR rather than a standard deviation to summarize spread? Explain.
Indicate the type and the nature of the actuators : Indicate the type and the nature of the sensors and transducers present in the plant and what additional sensors and transducers might be needed for properly operating and controlling the system.
What might explain guesses as low as 56 : You want a good guess of the professor's true height (or at least a good guess of how tall the students think the professor is). How would you summarize these data? Why? What might explain guesses as low as 56"?
Design a 4-bit carry-select adder : The report should include: the VHDL program, the captured logic circuit schematic diagram, the simulation waveform chart, the synthesis process report, and the FPGA CLB usage map; all produced by using Xilinx WebPACK ISE design software.
Build a client-server single-page app : For this assignment you are going to build a client-server single-page app that allows a user to retrieve and view superhero information from the server
Discuss the strategic direction of the company : Discuss the strategic direction of the company and whether you believe the organization to be on the right track. Make recommendations that you believe would help Dish to gain market share.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd