How much money could be saved annually

Assignment Help Mechanical Engineering
Reference no: EM13704093

A home has a total of 7.5 KW of lighting and the lights stay on 2/3 of the time. If electricity is priced at 12 cents/KWh, then how much money could be saved annually with a 25% reduction in use?

Reference no: EM13704093

Questions Cloud

Web search to locate the group''s main web site : Perform a web search to locate the group's main web site. Also, perform a web search for recent information about your group's activities. You can either type up your report as an essay or you can give your information in a bullet-point list. M..
Minimum amount of power this fan must consume to operate : A fan accelerates air (at atmospheric pressure and 300K) from a rest to 5m/s. The fan mass flow rate of air is 1.2 kg/s. What is the minimum amount of power this fan must consume to operate under these conditions?
Which is made of an aluminum pin of unknown diameter : A steel bar AC of length 6in and a varying cross-section is loaded as shown in fig 1. The bar is supported by a pin joint at A. which is made of an aluminum pin of unknown diameter.
Resource management policy : Historians have suggested that a significant environmental policy was implemented in the 1960s and 1970s in part because the political climate was ripe with a supportive public and leaders who were willing to act.
How much money could be saved annually : A home has a total of 7.5 KW of lighting and the lights stay on 2/3 of the time. If electricity is priced at 12 cents/KWh, then how much money could be saved annually with a 25% reduction in use?
Find the partial pressure of octane and the specific volume : In a car engine gasoline (assume octane C8H18) is evaporated and then mixed with air in a ratio of 1:15 by mass. In the cylinder the mixture is at 750 kPa, 650 K when the spark fires. For that time find the partial pressure of the octane and the spec..
Produced per gallon of burned gasoline : The EPA has mandated that car companies must meet certain average fuel efficiency for all cars they sell. What will this efficiency (in mpg) have to be by 2025 according to new laws? How much CO2 is produced per gallon of burned gasoline? At this new..
Air side and steam side of this heat exchanger : What is the shortcut equations used for evaluating the heat added to air by a steam coil. Use a sketch to present information on both the air side and steam side of this heat exchanger.
Lethal yellowing disease that kills palm trees : Lethal yellowing, disease that kills Palm trees, is moving across the Caribbean Islands at a rate of about 1 3/10 miles per month. How many months m will it take for the disease to spread a distance of 195 miles?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd