How heavy was the load in units of kilograms

Assignment Help Electrical Engineering
Reference no: EM13249829

A 100-watt motor (60% efficient) is used to raise a 100-kilogram load 5 meters into the air. If the task takes 65 seconds to complete, how heay was the load in units of kilograms?

Reference no: EM13249829

Questions Cloud

A complete mechanism for the reduction of a carboxylic acid : Draw the full and complete mechanism for the reduction of a carboxylic acid using H2 over platinum. The product is a primary alcohol. Just use ethanoic acid as your model compound.
Pricing strategies : Identity three types of pricing strategies. Select a good or service and compare the prices of two different companies associated with the goods or service.
Find the ratio of capacitors : Three identical capacitors are connected in series to give an equivalent capacitance CS, What is the ratio of CS/CP
Explain what is the enthalpy of the reaction : What is the enthalpy of this reaction. Assume that no heat is lost to the surroundings or to the coffee cup itself and that the specific heat of the solution is the same as that of pure water.
How heavy was the load in units of kilograms : A 100-watt motor (60% efficient) is used to raise a 100-kilogram load 5 meters into the air. If the task takes 65 seconds to complete, how heavy was the load in units of kilograms
What is hydrogen life cycle : How you can produce hydrogen? What is hydrogen life cycle ?
Compute the enthalpy change delta h : Calculate the enthalpy change, Delta H, for this reaction per mole of \rm X. Assume that the specific heat and density of the resulting solution are equal to those of water [4.18 \rm J/(g \cdot {^\circ C}) and 1.00 \rm g/mL] and that no heat is lo..
Older prehistoric paintings : What might account for the fact that we sometimes find prehistoric paintings done over older prehistoric paintings?
Natural selection theory : How would natural selection theory explain the presence of traits like psychological disorders and so on? If "survival is for the fittest" as evolution theory says, how come disorders and diseases are still around and did not disappear from the genet..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find the closest distance to the load plane

A 50 ohmlossless air transmission line is terminated in a load impedance ZL = 12.5 + j20 ohm. Find the following using a Smith Chart: the load admittance YL. the closest distance to the load plane where the normalized admittance on the line is 1 + j..

  What happens to the propagation delay of n-bit full adder

What happens to the propagation delay of the N-bit full adder as N is increases from 2 bits to 32 bits Compare and contrast this method of building an adder with the carry look ahead method described in your textbook

  Design the current divider so that the resistors are less

Design a current divider that will provide a 1/3-2/3 current splitting ratio. Use resistance in kilo ohm range. Redesign the current divider so that the resistors are less than 100 ohms but maintain the same 1/3-2/3 splitting ratio.

  Calculate the built-in voltage of a junction

Calculate the built-in voltage of a junction in which the p and n regions are doped equally with 10^16 atoms/cm3. Assume ni =.5x10^10/cm^3.  With the terminals left open, what is the width of the depletion region

  Explain power factor

Power Factor, A single phase electric motor has an output power of 10 kW and an efficiency of 90% at full load. The motor is fed from a 240 V supply via a cable that has a resistance of 10 milli ohms per metre length.

  Determine what is the probability of false alarm

A spread-spectrum acquisition system uses a serial search scheme.The synchroniser integrates the squarer output for interval of 0.1s and the synchroniser output is sampled at intervals of 0.05s . The probability of false alarm is 0.064255 .

  What would be the required dc input power

A modulating signal is amplified by a 80% efficiency amplifier before being combined with a 20 kW carrier to generate an AM signal. what would be The required DC input power to the amplifier, for the system to operate at 100% modulation.

  What kind of wireless networking alternative

What kind of wireless networking alternative makes the most sense when considering network links that span an appreciable portion of the globe?

  How is the problem-solving process different

How is the problem-solving process different when programming in assembly language versus programming in ladder logic?

  Determine the transfer function for a first order filter

Determine the transfer function for a first order low pass filter with a cutoff frequency of 1000 radians per second and passband gain of 1 using Chebyshev type with 1-dB ripples on the passband.

  Determine what villages will the meyer read now

A student acquires a 50mV, 1mA (meter-A) and a 50mV , 2mA (Meter-b) d'arsonval movements and converts both the meters to measure 100v full scale individually. A potential divider consisting of 70k and30k resistors was powered using an ideal 100v D..

  What is the most common used op-amp in the industry

1) What are some practical op-amp applications Can you give example and explain why the bop-amp was used in your example 2) What is the most common used op-amp in the industry

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd