Find value of vov nd vgs required to cause device to operate

Assignment Help Electrical Engineering
Reference no: EM13251043

Consider a CMOS process for which Lmin = 0.25 ?m, tox = 6 nm, n= 460 cm2/Vs, and Vt= 0.5 V.

(a) Find Cox and

(b) For an NMOS transistor with W/L = 15 m/0.25 m, calculate the values of VOV , VGS, and VDSmin needed to operate the transistor in the saturation region with a dc current ID= 0.8mA.

(c) For the device in (b), find the value of VOV and VGS required to cause the device to operate as a 500-ohm resistor for very small vDS.

Reference no: EM13251043

Questions Cloud

Define what temperature in degrees celsius : The activation energy of a certain reaction is 47.9 kJ/mol. At 27 Celsius, the rate constant is 0.0120 s^-1. At what temperature in degrees Celsius would this reaction go twice as fast
Find the response of the system if x is equal to u : A causal discrete LTI system is described by y(n)-3/4 y(n-1)+1/8 y(n-2)=x(n) where x(n) is the input and y(n) is the output Find the response of the system if x(n) =u(n)
What is the resulting ucl value for the line : From the samples you determine the fraction defective is 0.05 and the standard deviation is 0.01. If the desired confidence level is 99.7 percent, what is the resulting UCL value for the line?
Explain what temperature does the numerical reading : At what temperature does the numerical reading on a Celsius thermometer equal that on a Fahrenheit thermometer
Find value of vov nd vgs required to cause device to operate : (a) Find Cox and (b) For an NMOS transistor with W/L = 15 m/0.25 m, calculate the values of VOV , VGS, and VDSmin needed to operate the transistor in the saturation region with a dc current ID= 0.8mA.
What is total quality management : What is total quality management? What are the major characteristics of total quality management?
Determine the buoyant force on the cylinder : An aluminum cylinder is suspended in an unknown fluid by a spring scale. Outside the fluid, the object weighs 20N. In the fluid,
What information do managers need to make that decision : Describe three basic decisions that must be addressed in the design of operations systems. For each decision, what information do managers need to make that decision?
Determine the emf of the cell : A solar cell generates a potential difference of 0.320 V when a 445.0 ? resistor is connected across it and a potential difference of 0.504 V when a 945.0 ? resistor is substituted. What is the emf of the cell

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Explain which parameter of an fm transmission determines

Do either or both of the reasons you gave in part (a) above also apply to a point to point voice link using frequency modulation? c. Which parameter of an FM transmission determines whether it is wideband or narrow band?

  The maximum demand estimation

The circuit arrangements for each of the installations, the final circuit cable selection, the maximum demand estimation, and the circuit protection arrangements should be designed.

  Find the tension in the rope

A newly planted tree is supported against the wind by a rope tied to a stake in the ground. The force of the wind, though distributed over the tree, is equivalent to a single force F. Find the tension in the rope

  Define a set of digital scales is required to measure a load

A set of digital scales is required to measure a load of 1000 N with an accuracy of ±1 N. Determine the minimum output resolution of the required ADC.

  Does the sampling rate meet nyquist condition

A continuous time system, describes by y(t) = 5 Cos (2*pi*20*t+pi/2), is sampled at rate 320 Hz. a) Write the mathematical expression that describes the discrete time (sampled) signal. b) Calculate the value of the discrete signal for n=0 and n=4.

  Define circuit analysis

Bode plots were introduced in my second circuit analysis class, but I really didn't think it was important because it looked like an outdated tool no longer in use.

  Methods used to eliminate noise from a spatio-temporal

Methods used to eliminate noise from a spatio-temporal signal, Name and describe, in detail, 2 methods used to eliminate noise from a (spatio-temporal) signal. This question requires a clear, detailed explanation of the methods. Mathematical equation..

  What is percent quantization error if 1volt max signal input

A unipolar 16 bit ADC measures 0-10 volts full scale. a) What is the minimum resolvable voltage b) What is the percent quantization error c) What is the percent quantization error if a 1 volt max signal is input

  Find the complex exponential forier series of the signal

The signal given is x(t) =cos(440*2*pi*t) +cos(554*2*pi*t)+cos(659*2*pi*t) Find the complex exponential forier series of the signal and plot k vs Ck for k=-1000 to 1000.

  Find the probability of bit errors occurring in the frame

Let the probability of a bit error be p, and the length of a data frame be N. Find the probability of 1, 2, 3, and 4 bit errors occurring in the frame. a) Tabulate the results for N = 1000, 10000, and 100000 bits, for p = 10-6, 10-8, and 10-14

  Implement the relative addressing mode

Write an optimal sequence of control microinstruction

  Determine what is the value of the voltage source

A two-resistor voltage divider consists of a 10 k and a 15 k ohm resistor, with the 10 k resistor connected to the voltage source and the 15 k resistor connected to ground. If the output voltage is 2.5 V across the 10 k resistor

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd