Find out a compression ratio and inlet pressure

Assignment Help Mechanical Engineering
Reference no: EM13216722

An SI engine operating on a four-stroke air-standard cycle using stoichiometric gasoline is to have a maximum cylinder pressure of 11,000 kPa at WOT. Inlet pressure can be 100 kPa without supercharging, or it can be as high as 150 kPa with a supercharger. Design the engine cycle and pick a compression ratio and inlet pressure combination to give maximum indicated thermal efficiency. Also find out a compression ratio and inlet pressure to give maximum imep. engineering fundamentals of internal combustion enignes - pulkrabek.

Reference no: EM13216722

Questions Cloud

Consider a metal single crystal oriented : Consider a metal single crystal oriented such that the normal to the slip plane and the slip direction are at angles of 43.1
Elements of an effective medical office financial policy : What are the basic elements of an effective medical office financial policy? In what ways do medical office procedures support financial policies? What are the consequences when office procedures do not support the financial
Find the tension in ropes a and b : a 100 pound ball is suspended from a wall by a rope that is pulled asided by a horizontal rope B and held so that rope A makes a angle of 30 degrees with the vertical wall. Find the tension in ropes A and B?
Implementation of project portfolio management : Implementation of project portfolio management should be initiated by the top managers, executive and high level managers should be committed to the portfolio management system first and then influence the team to be committed to the system.
Find out a compression ratio and inlet pressure : Also find out a compression ratio and inlet pressure to give maximum imep. engineering fundamentals of internal combustion enignes - pulkrabek.
A peace treaty was not signed until nearly two years : A peace treaty was not signed until nearly two years after the surrender at Yorktown because
Determine the tensions at the cables : the suspended load exerts a force F=600 lb at A, and the weight of the bar OA is negligible. Determine the tensions at the cables and the reactions at the ball and socket support O
Explain the offeree did intend to accept a particular offer : How would an offeror prove that the offeree did intend to accept a particular offer if the offeree contended that she was only joking, or that she didn't know that an offer was being made
The trait theories of personality : What did you learn about yourself from reading about the trait theories of personality? What did you learn about yourself from reading the other theories of personality? (List and explain at least three things.) How will you use this material to impr..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd