Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A steel bar is attached to a wood support beam with four 20 mm diameter lag screws. The steel bar is 75-mm-wide by 6-mm-thick. For the steel bar, the yield strength is 260 MPa and the ultimate bearing strength is 350 MPa. The ultimate shear strength of the lag screws is 165 MPa. Factors of safety of 1.70 with respect to yield strength and 3.1 with respect to bearing strength are required for the bar. A factor of safety of 3.0 with respect to the ultimate shear strength is required for the lag screws. Determine the allowable load P that can be supported by this connection. (Note: Consider only the gross cross-sectional area of the bar not the net area.)
A light rail route has 2 terminals and 4 intermediate stations. The demand (passengers/hr) for morning peak hour is: North Terminal Station 1 Station 2 Station 3 Station 4 South Terminal
A MH at an intersection has an inflow from three 8-inch PVC (n = 0.01) sanitary sewer pipes laid at minimum slope converging at an intersection and one pipe taking the flow from those three further downstream.
A fluid flowing in a pipe 30cm in diameter has a uniform velocity of 4m/s. The pressure at the center of the pipe is 40KPa, and the elevation of the pipe's centerline above an assumed datum is 4.5m. Compute the total energy per unit weight of the ..
A fluid film 0.1 mm thick separates solid and surface. The fluid viscosity is 0.04 N*sec/m^2. Assuming the velocity distribution in the film is linear, find the terminal velocity of the block. The area of the cube in contact with the film is 0.25 ..
given that E for the tube material is 70 GN/m2 and the stool legs are 75cm long, how much will each leg shorten under the applied compressive load (take g = 9.8m/s2)
A building frame is made with a 10" square steel box shape that has an area of 15 in^2 and a moment of inertia I =225 in^4. The frame consists of pinned supports at points A and F and an internal pin at point D.
The 70 m tall tower is supported by three cables that exert forces FAB, FAC, and FAD on it. The magnitude of the force FAB is 2 kN. The x and z components of the vector sum of the forces exerted on the tower by the three cables are zero. What are ..
A cantilever beam of length 50 ft is embedded in a wall at A and has a free end B. A concentrated load of 100 kips upward is located at x = 25 ft from A. A uniformly distributed load of 20 kips/ft downward extends from 25 to 50 ft.
A flow has circular streamlines. At t=0 the flow is in the clockwise direction and the angular velocity is pi rad/s. This flow exists for 1 s, and then reverses to counterclockwise with an angular velocity of -pi rad/s for 1 s.
calculate the cracking moment (resisting moment) for an unreinforcedconcrete beam that is 10 in. wide, 16 in. high. assume normal weight concrete with 3000 psi = f prime sub c. use the internal couple method and check with the flexure formula.
Q. What is the main objective of NASA's Mars Science Laboratory (MSL) mission? When was it launched and when and where is it scheduled to land on Mars? Explain the major differences between this mission and Mars Exploration Rovers (MER) mission?
An 8.5 m compacted fill is to be placed over the soil profile. Consolidation tests on samples from points A and B produced the following results. a) Calculate the consolidation settlement caused by the weight of this fill.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd