Determine which dislocation segment moves

Assignment Help Mechanical Engineering
Reference no: EM13856922

1. An L shaped edge dislocation ABC in a crystal is shown in Figure below. The stresses acting on the crystal are also shown. Determine which dislocation segment moves and which dislocation segment does not move. What will be the shape of the crystal when the dislocation segment moves continuously. Can you observe these movements in the TEM in-situ if the dislocation is present in a foil. If you can only apply tensile components in the TEM stage, show how the tensile stresses should be acting.

679_DefectsInSolids.png

2. A screw dislocation in an fcc crystal with Burgers vector of the type a12 [1101 has split into Shockley partial dislocations of the a/2 <112> type. Thus AB=A8i-6b. Does the split configuration of the dislocation have any hydrostatic component of stress. If it has, determine the hydrostatic stress assuming a separation, d, between the partial dislocations. Does it vary as hr or as 1r 2 at large distances compared to d. Here, r, is the radial distance from the center of the position of the partial dislocations.

3. In a GaAs film grown on Si crystal, two 60 degree dislocations combine to form a 90 degree dislocation with Burgers vector [(a/2)[1-10]. The sense vectors of all the dislocations are parallel to each other and remain along [110] as shown in figure below. Assign the Burgers vectors of all the three dislocations using the Thompson tetrahedron. Is it energetically favorable or a stress is needed to assist the combination. Construct an image dislocation model with respect to the free surface shown. Assume the two dislocations are situated at a height h 1 from the free surface. Write the total energy in terms of self and interaction energy terms without actually calculating the total energy. Note the right handed coordinate system is chosen with [110] perpendicular to the plane and [1-10] lying in the plane. [001] is perpendicular to the free surface of the GaAs film.

1380_DefectsInSolids2.png

Reference no: EM13856922

Previous Q& A

  Discuss the purpose and role of the angel

Discuss the purpose and role of the angel

  Determine the various ways the film version departs

Examine and determine the various ways the film version departs from and/or adheres to the original play. Then offer reasons why these differences were more (or less) effective than the original

  Write a play about you writing your play

Word to the Wise: Do not write a play about you writing your play. This has been done to death, isn't nearly as creative as it seems late at night, and kinda pisses off the instructor

  How do you exchange business cards

How do you exchange business cards and how do you explain your position and your bosss position

  Describe an instance of miscommunication based on nonverbal

Describe an instance of miscommunication based on nonverbal communication by providing an example of a time when you nonverbally communicated something other than what you meant.

  How ccss are used within school for teaching and learning

Explains the purpose of CCSS. Explains how the CCSS are used within a school for teaching and learning. Justifies why creating report cards based on the CCSS is important in the school or district (depending on the role you chose to take as noted i..

  Shopping over the last couple of decades

Give a brief historical background on the growth in online shopping over the last couple of decades. (approximately 400 to 500 words)

  Demonstrate knowledge of current research

Demonstrate knowledge of current research and evidence of wide reading and demonstrate a critical reflective approach to an evidenced-based review of the literature - Literature Review in Aged Services

  Does the essay present an effective argument?

Effectiveness of the overall argument. Does the essay present an effective argument? Address the counterarguments? Use logical and relevant examples?

  Calculate the price elasticity of demand

In the United States, 2007 was a bad year for growing wheat. And as wheat supply decreased, the price of wheat rose dramatically, leading to a lower quantity demanded (a movement along the demand curve). The accompanying table describes what happe..

Reviews

Write a Review

 

Similar Q& A

  Show that maximum stored kinetic energy per unit mass of

for a spinning solid circular disk of radius a and constant thickness the maximum stresses occur at thenbspcenter of

  Use 3 terms of taylor series to estimate the velocity at

the velocity of falling parachute is computed asvtgmc 1-e-cmtwhere g9.8ms2 m50kg c12.5.use 3 terms of taylor series to

  A solid cube of wood having dimensions of 05 m3 is

a solid cube of wood having dimensions of 0.5 m3 is floating in water with 0.3 m of its dimension above the surface.

  Steam enters diffuser operating steady state with pressure

Steam enters a diffuser operating at steady state with a pressure of 14.7 psi, a temperature of 300F, and a velocity of 500ft/s. Steam exits the diffuser as a saturated vapor with negligible kinetic energy. Heat transfer occurs from the steam to its ..

  Air undergoes a isentropic compression in a piston-cylinder

air undergoes a isentropic compression in a piston-cylinder assembly from p1- 1atm t1 70 f to p2 5 atm. assuming air

  What is the thermal and mechanical efficiency

What is the thermal and mechanical efficiency for this engine when used as heat pump and refrigerator with the following propties;

  Assume that the mercury 50 operates on an ideal brayton

solar turbines mercury 50 gas-turbine power generatorinlet air temperature 300 kinlet air pressure 100 kpa atmospheric

  A plate of stainless steel has a thickness of 30 cm and is

a plate of stainless steel has a thickness of 3.0 cm and is initially uniform in temperature at 500c. the plate is

  A 23 kg crate rests on a 10 kg hand cart as shown the

a 23 kg crate rests on a 10 kg hand cart as shown. the center of mass of the combined cratecart is at c. the cart is

  Solve using the ideal-gas law the generalized

solve using the ideal-gas law the generalized compressibility factor and steam tables. compare the specific volume of

  Two points b and c lie on radial line of a rotating disk

two points b and c lie on radial line of a rotating disk. the points are 2 inches apart. vb700 ftmin and vc880ftmin.

  Ideal gas model for the air and variable specific heats

Air at 300 kPa, 63oC, and a velocity of 423 m/s enters an insulated duct of varying cross-sectional area. The air exits at 150 kPa, 88oC. At the inlet, the cross-sectional area is 6.57 cm2.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd