Determine the rate of entropy generation during this proces

Assignment Help Mechanical Engineering
Reference no: EM13719329

Nitrogen (N2) gas at 100 kPa and 298 K enters a compressor steadily with a mas flow rate of 2 kg/s. The nitrogen leaves at 800 kPa and 580 K. Asume the compressor is well insulated. Do NOT assume the specific heats of the nitrogen as constant or a linear function of temperature.

Determine:

A) the rate of entropy generation during this process

B) if the process is reversible, irreversible or impossible.

Reference no: EM13719329

Questions Cloud

Encompasses an incredible diversity of topics : Materials science engineering deals with materials and encompasses an incredible diversity of topics and problems were constituting the four elements of the field (i.e. processing, structure, properties, and performance). In which scenario could a ma..
A gas has a volume of 50.0 cm3at a temperature : A gas has a volume of 50.0 cm3at a temperature of -73°C. What volume would the gas occupy at a temperature of -123°C if the pressure stays constant?
Hydrogen gas can be produced in the laboratory : Hydrogen gas can be produced in the laboratory through the reaction of magnesium metal with hydrochloric acid: Mg(s)+2HCl(aq)→MgCl2(aq)+H2(g)
The george zimmerman case has gained national attention : The George Zimmerman case has gained national attention, focusing on the Florida Statute, "Stand your Ground" law. Included in the Power point is the specific stand your ground law existing in Florida. review the statute and the news story, an..
Determine the rate of entropy generation during this proces : Nitrogen (N2) gas at 100 kPa and 298 K enters a compressor steadily with a mas flow rate of 2 kg/s. The nitrogen leaves at 800 kPa and 580 K. Asume the compressor is well insulated. Do NOT assume the specific heats of the nitrogen as constant or a li..
What rate must heat be supplied to this system : A 514.0 g/hr stream of liquid methyl alcohol, also called methanol, (CH3OH) at 6.80 atm and 36.0°C was held at constant pressure, vaporized and brought to 240.0°C. At what rate must heat be supplied to this system? Assume that methyl alcohol vapor be..
Bearing is subjected to the loads-inner race rotate : The bearing (inner race rotate) is subjected to the loads as shown in Fig. 2 (next page). The shaft diameter is 30 mm. The shaft rotates at 655 rpm for 9000 hours life. Select ball bearings (load rating) for position A and C. Assume initial values. X..
Calculate the damped natural frequency : We are learning about oscillations and second-order dynamic systems. We observe a crane at a construction site on campus and notice that as soon as the crane operator releases the load, the whole crane oscillates back and forth several times as the v..
Electron in hydrogen atom is found in tunneling region : The probability that the 1s electron in the hydrogen atom is found in the tunneling (classically forbidden) region. The probability that the 1s electron in the Ne+9 is found in the tunneling region. By this measure, is a 1s electron in Ne+9 more or l..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd