Determine the radial location of the unbalanced mass

Assignment Help Mechanical Engineering
Reference no: EM131146142

A turbine rotor of mass 200 kg has an unbalanced mass of 15 kg. It is supported on a foundation which has an equivalent stiffness of 5,000 N/m and a damping ratio of If the rotor is found to vibrate with a deflection of 0.1 m at resonance, determine:

(a) the radial location (eccentricity) of the unbalanced mass,

(b) the additional mass to be added (uniformly) to the rotor if the deflection of the rotor at resonance is to be reduced to 0.05 m, and

(c) the peak deflection of the turbine when the frequency ratio (r) varies.

Reference no: EM131146142

Questions Cloud

Derive the equation of motion of the mass m : Derive the equation of motion of the mass m shown in Fig. 3.66 when the pressure in the cylinder fluctuates sinusoidally. The two springs with stiffnesses k1 are initially under a tension of T0. and the coefficient of friction between the mass and ..
How positive conflict can increase the overall productivity : Z Corporation has been investigating how positive conflict can increase the overall productivity of a project team. They have asked you to take a new project team and use this methodology in its compilation and execution. The team is comprised of one..
Difference in research proposal and final research report : Discuss the difference between a research proposal and a final research report. Discuss the perceptions of the research "misconceptions" (what research is and is not). Explain your perceptions of the difference between theoretical and administrative ..
Retention Management : Which of the following is an attribute of a high value employee that an organization would want to prevent from leaving?
Determine the radial location of the unbalanced mass : A turbine rotor of mass 200 kg has an unbalanced mass of 15 kg. It is supported on a foundation which has an equivalent stiffness of 5,000 N/m and a damping ratio of If the rotor is found to vibrate with a deflection of 0.1 m at resonance
Effective communication lead to effective organization : You have completed an analysis on a company that is experiencing low morale, high turnover rates, and overall employee discontent. As an external change agent, you have seen this pattern before in previous organizations, where managers make decisions..
Excellent strategic management showcased : Read “Excellent Strategic Management Showcased: Priceline.com Inc.” on page 90 of your course textbook. As you read, pay close attention to Priceline’s strategy, and write a case study describing the following points: What are Priceline’s internal st..
Determine whether the vortex shedding around the antenna : The first two natural frequencies of the telescoping car antenna shown in Fig. 3.68 are given by 3.0 Hz and 7.0 Hz. Determine whether the vortex shedding around the antenna causes instability over the speed range 50 75 mph of the automobile.
Target market characteristics : Marketing - How do target market characteristics determine which promotional methods to include in a promotion mix? Assume a company is planning to promote a cereal to both adults and children. Along what major dimensions would these two promotional ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the initial mass of liquid water if piston hits

frictionless piston in a cylinder with 0.2 kg h2o under it. if piston raises to a given height the piston will hit

  What difference would you expect in their ability to protect

Steel products are commonly protected by chromium or zinc coatings. Based on the galvanic series, what difference would you expect in their ability to protect steel?

  Kilogram of polychloroprene

Fifteen kilogram of polychloroprene is vulcanized with 5.2 kg sulfur. What fraction of the possible crosslink sites is bonded to sulfur crosslinks, assuming that, on the average, 5.5 sulfur atoms participate in each crosslink?

  Determine the exit temperature and the power input assuming

air at 100 kpa and 27degc enters an isentropic compressor at a rate of 100 ls and leaves at 1000 kpa. determine the

  Maximum efficiency of the heat exchanger

Maximum efficiency of the heat exchanger to be able to realise the highest possible fuel economy improvement3. Durability of 150,000km (legal requirement for emission relevant components)

  What is the probability that the strength is less

What is the probability that the strength is less than or equal to 5,000 psi. What is the probability that the strength is greater than 2,500 psi

  Reversibly until the first droplet of liquid forms

A piston-cylinder assembly initially contains 4 mol of substance X in vapor phase at 0.8 bar and 373 K. The vapor is compressed isothermally and reversibly until the first droplet of liquid forms.

  A 10 kg slab of cr-v steel at 900 c is to be quenched by

a 10 kg slab of cr-v steel at 900 c is to be quenched by immersing in a vessel of water. assume the slab exhibits a

  List all assumptions and show all calculations is this the

a rubber stopper covers the drain in your bathtub. estimate the force that the water exerts on the stopper. list all

  What quantity of solid copper should be used

A batch of 20 tons of liquid copper is to be cooled from 2350°F to 2200°F by adding solid copper at 77°F . Assume no heat loss. What quantity of solid copper should be used?

  Hence calculate the average thickness of the water film

question a person of weight 100 kg standing on skis 2 m long and 0.10 in wide slides on the 2deg mountain slope at

  If the temperature of the inner and outer surfaces of the

heat is transferred steadily to boiling water in a pan through its flat bottom at a rate of 650 w. if the temperature

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd