Determine the potential difference between the two ends

Assignment Help Electrical Engineering
Reference no: EM13272196

A conducting bar of length l rotates about one end in a uniform magnetic field at a frequency of ω rad/sec. Determine the potential difference between the two ends using
(a) Faraday's law of induction.
(b) Using the Lorentz force equation F = q(E + v x B).

Reference no: EM13272196

Questions Cloud

How much energy is exchanged when a positive charge moves : Supposed that the terminals are labeled a,b. V(ab) = -15 V, how much energy is exchanged when a positive charge of a 4 C moves through the device from a to b. Is the energy delivered or taken from the device.
Should the project be pursued : The truck falls into the MACRS five year class life(applicable annual percentages are 20%, 32%, 19%, 12%, 11% and 6%) and the truck will be sold after two years for $40,000.
Explain an evaluation of r was performed : An evaluation of R was performed, following the procedure described in this module. The barometric pressure was 736 torr, the temperature was 295k and volume of hydrogen gas collected was 35.6 mL.
What is the subscription price : Keira Mfg. is considering a rights offer. The company has determined that the ex-rights price would be $76. The current price is $90 per share, and there are 36 million shares outstanding. The rights offer would raise a total of $60 million. What ..
Determine the potential difference between the two ends : A conducting bar of length l rotates about one end in a uniform magnetic field at a frequency of ω rad/sec. Determine the potential difference between the two ends using (a) Faraday's law of induction.
Complete a reading analysis and report writing task : Complete a reading analysis and report writing task - write an Introduction describing (a) the title of the article, (b) the author/s; (c) who/what the article is about, and (d) finish with a short paragraph about why the authors wanted to do the s..
How much helium is lost per hour : A physicist uses a cylindrical metal can 0.300m high and 0.070m in diameter to store liquid helium at 4.22 K; at that temperature the heat of vaporization of helium is 2.09×104J/kg. How much helium is lost per hour
What is the stock expected total return : If D1=$1.25, g(which is constant)=5.5%, and P0=$44, what is the stock's expected total return for the coming year?
Express the result in cylindrical and rectangular components : Express the field D = ( x + y ) ( x + y ) a)in cylindrical components and cylindrical variables b) Evaluate D at the point where = 2 , = 0.2 , and z = 5, expressing the result in cylindrical and rectangular components.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What value of crystal is needed with a divide factor

A PPL multiplier transmitter is to operate with a 915 MHz output. With a divide factor of 64, what value of crystal is needed

  How the clamping circuit adds or subtracts a dc component

1) How would you identify the anode of an unmarked diode using a DMM (Digital Multimeter)  2) Explain how the clamping circuit adds or subtracts a DC component to an input voltage.

  Explain watts in cassette players

Watts in Cassette Players, A walker's cassette tape player uses 4 AA batteries in series to provide 6V to the player circuit. The four alkaline battery cells store a total of 200 watts-second of energy.

  Why are rf amplifiers necessary in fm receivers

1. What parameter of the intelligence signal causes or determines the rate of carrier frequency deviation 2. If you are tuned to an FM station at a frequency of 100.1 MHz, show the bandwidth allocation for two adjacent stations.

  What is the clearance requirement for three-wire service

What is the clearance requirement for a 120/240 V, single-phase, three-wire service at the point of attachment to the building Over the driveway Over the main roadway

  Design to test an op-amp based instrumentation amplifier

Design (simulaton, analysis), build and test an op-amp based instrumentation amplifier with the following specifications: (a) Have very high input resistance (minimum is 1 Mega Ohm). (b) Have very high voltage gain (minimum 1000V)

  Explain zener diode and series resistance

Zener Diode and Series Resistance, In the zener diode circuit calculate the value of the current through the zener diode if the power supply is rated 24 volts at 500 milli amperes

  Find what is the value of the voltage source

A Two resistor voltage divider consists of a 10k ohm and a 15k ohm resistor, with the 10k ohm resistor connected to the voltage source and the 15k ohm resistor connected to ground. if the output voltage is 2.5V

  Explain an electric heating element is connected

An electric heating element is connected to a 110 v circuit and a current of 3.2 A is flowing through the element. How much energy is used up during a period

  What is the expected output for an input voltage

A HCS12 ATD has been set-up to perform a right-justified, 10-bit, signed operation. What is the expected output for an input voltage of 3.09V The voltage range is 0-5V.5V/4096 = 4.88 mV.

  What is the magnitude of the current that flows through wire

A wire carrying a current is shaped in the form of a circular loop of radius 4.0 mm. If the magnetic field strength at its center is 1.1 mT with no external magnetic fields contributing to it, what is the magnitude of the current that flows throug..

  What is frequency that corresponds to frequency bin number

A DSP engineer applies DFT to 500 data samples that are sampled at 250 Hz to plot the signal spectrum. What is the frequency that corresponds to the frequency bin number

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd