Determine the net work output and thermal efficiency

Assignment Help Mechanical Engineering
Reference no: EM13711521

A gas turbine power plant operates on the simple Brayton cycle between the pressure limits of 100 and 1600 kPa. The working fluid is air, which enters the compressor at 40 degrees Celsius and leaves at 650 degrees Celsius. Using constant specific heats for air and assuming a compressor isentropic efficiency of 85% and a turbine isentropic efficiency of 88%, determine (a) the net work output, (b) the thermal efficiency. The cut off ratio of the cycle is 2.6. Assume constant specific heats for air at room temperature (Cp=1.005 KJ/kg.K and k=1.4)

Reference no: EM13711521

Questions Cloud

The pressure is maintained constant in the cylinder : A piston-cylinder device contains 12 kg of saturated R-134a vapor at 3.2 bars. An electric source supplies 8 A current to a resistor within the cylinder for 4 minutes and there is heat transfer of 400 kJ to the system. During these energy interaction..
Velocity of the fluid at the nozzle exit : Show that the thrust developed by a stationary rocket motor is F = rho*A*U^2 + A(p- p_atm) where p_atm is the atmospheric pressure, and p, rho, A, and U are, respectively, the pressure, density, area, and velocity of the fluid at the nozzle exit.
Statement regarding the fracture of materials : Polymer fracture is highly dependent on the testing conditions, such as temperature and strain rate, but is not affected by the nature of bonding of the molecular chains. For metals, fracture only occurs along the boundaries created by the differentl..
Vibration of the cone as function of the forcing frequency : A speaker driver can be modeled as a one degree of freedom forced system with damping. The mass of the moving cone is m=0.1 kg and the spring k=50000N/m.
Determine the net work output and thermal efficiency : A gas turbine power plant operates on the simple Brayton cycle between the pressure limits of 100 and 1600 kPa. The working fluid is air, which enters the compressor at 40 degrees Celsius and leaves at 650 degrees Celsius. Using constant specific hea..
What is the convective heat transfer : A square vertical plate measuring 0.25 m on each side is exposed on one side to air at 1 atm and 10 C. If the plate is held at a constant 286 C, what is the convective heat transfer?
Find the convective heat transfer in the channel : Two plates are suspended vertically in 20 C atmospheric air forming a channel of width 18cm. The plates are 3m high and are maintained at a temperature of 275 C. If the channel is 5 m deep, find the convective heat transfer in the channel
Rate of heat transfer between the steam and cooling water : A shell-and-tube heat exchanger is used to cool a flow of steam using a stream of cooling water. The steam enters the heat exchanger at 0.1 bar and a quality of 91% (state 1), and exits as a saturated liquid at the same pressure (state 2).
Determine the centroidal moment of inertia : Determine the centroidal moment of inertia for the following. The center circle is cut out. you have a rectangle standing up ward the height is 7 in and the width is 4 in there is a cut out hole in the center with 2 in for diameter.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd