Determine the maximum horizontal displacement

Assignment Help Mechanical Engineering
Reference no: EM13212314

The 1.8-kg block A slides in the smooth horizontal slot. When the block is given an initial velocity of 18 m/s to the right. Determine the maximum horizontal displacement s of the block. Each of the two springs has a stiffness of k = 2500N/m and an unstretched length of 0.15 m.

Reference no: EM13212314

Questions Cloud

Find out the equiibrium pressure of no2 : A reaction mixture initially contains 0.86 M NO and 0.86 M S03. Determine the equiibrium pressure of NO2 if Kc for the reaction at this temperature is 0.0118.
Would balanced budget requirement make nations real income : Consider the following model of a closed economy in which household income taxes are proportional to income: Yd = C + I + G C = 200 + 0.80(Y-T) Y=Yd I=600 T= 0.20 Y G = 1000 a. What is "autonomous expenditure" for this economy
Determine the exit temperature : Determine (a) the exit temperature, (b) the exit relative humidity of the air, (c) the exit velocity.
Determine the expressions for the principal stresses : A circular shaft is subjected to a torque Ta and a bending moment Ma. Assuming that the diameter of the shaft is d, determine the expressions for the principal stresses and maximum shear stress in terms of Ma, Ta and d.
Determine the maximum horizontal displacement : Determine the maximum horizontal displacement s of the block. Each of the two springs has a stiffness of k = 2500N/m and an unstretched length of 0.15 m.
State what affect will adding more so3 have on the system : Consider the following reaction at equilibrium. What affect will adding more SO3 have on the system?
Calculate the power output in kw : Air enters a turbine at 40 kN/m2, 900 C, and leaves at 10 kN/m2. The flow is reversible and adiabatic. Inlet velocity is quite low and outlet velocity is 150 m/s through a cross-sectional area of 0.20 m2. Calculate the power output in kW.
Plot the moment about b : Plot the moment about B for 320mm
State the equation for an electrochemical cell reaction : Predict the immediate effect of the following changes on the observed cell voltage E.Increased E,Decreased E,No change E.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Explain employing the ideal gas model

Employing the ideal gas model, determine the change in specific entropy between the indicated states, in Btu/lbmol?ºR. Solve 2 ways: Use the appropriate ideal gas table AND also by using a constant specific heat value.

  Determine the reactions of simply supported

Determine the reactions of simply supported beam to both a concentrated and uniform load. A beam with a span of 21 ft is simply supported at the left-hand end and fixed at the right-hand end.

  Explain discharges to a nozzle for additional thrust

In the an ideal turbo jet, the engine is designed such that the turbine work is divided equally between the compressor and the propeller. The gas from the turbine discharges to a nozzle for additional thrust.

  What gas pressure will the experimenter measure in bulb

What gas pressure will the experimenter measure inside the bulb, A glass bulb contains air at room temperature and at a pressure of 1 atmosphere. It is placed in a chamber filled with helium gas at 1 atmosphere and at room temperature

  Compute the force required to punch out a rectangular

Calculate the force required to punch out a rectangular hole 100m x 50mm in a 2mm thick aluminium sheet. The ultimate strength in shear is 125 MN/m^2.

  Control the sequence of cylinder operations

State the sequence in which the cylinders operate on the operation of the start valve and show, with the aid of a schematic diagram, how an electronic controller could be included in the circuit to control the sequence of cylinder operations.

  A hydraulic cylinder is diameter

A hydraulic cylinder is 100mm diameter and is fed by a pipe 15mm in diameter. If the piston in the cylinder moves forward at a rate of 0.2ms^1

  Drilling fluid engineering manual

Read the titled books Drilling Fluid Engineering Manual. Textbook prepared by M-I Drilling Fluids Co.,1998; Halliburton Cementing Tables. Casing and cement data tables prepared by Halliburton Company.

  Determine the turbine work output

Determine (a) the turbine work output, in kJ/kg, and (b) the thermal efficiency of the cycle. Also, show the cycle on a T-s diagram with respect to saturation lines.

  How does data screening differ from data cleaning

.How does data screening differ from data cleaning?

  Determine the maximum shear stress

Draw the Mohr's circle for this stress state, deterrnine the principal stresses and the angle of the principal direction to the x-axis and determine the maximum shear stress.

  Explain what is the mass flow rate

Water enters a 2 meter diameter pipe at a temperature of 23 deg C. The water leaves the pipe at a temperature of 97 deg C The laminar flow rate is such that the Reynolds number is 800. What is the mass flow rate?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd