Determine the magnitude of the boats acceleration

Assignment Help Mechanical Engineering
Reference no: EM13216876

Starting from rest the motorboat travels around the circular path,P = 50m , at a speed v=(0.8t)m/s, where t is in seconds. Determine the magnitude of the boat's velocity when it has traveled 40m. Determine the magnitude of the boat's acceleration when it has traveled 40m.

Reference no: EM13216876

Questions Cloud

Determine the normal force r between the wheel : Determine the normal force R between the wheel and the horizontal surface. Neglect the weight of the horizontal shaft.
Define the four types of evaluation outcomes : Describe the three kinds of knowledge that can be evaluated in training and how they can be measured. Explain the four types of evaluation outcomes identified in the text.
Compute the atomic packing factor : the unit cell for uranium has orthorhombic symmetry, with a, b and c lattice parameters of 0.286, 0.587 and 0.495nm, respectively. if its density, atomic weight, and atomic radius are 19.05g/cm3, 238.03g/mol and 0.1385 nm respectively, compute the..
What restriction justifies limitation on his speech : murray orr is arrested for screaming obscenties on his front lawn at 3:00 in the morning. what restriction justifies limitation on his speech?
Determine the magnitude of the boats acceleration : Starting from rest the motorboat travels around the circular path,P = 50m , at a speed v=(0.8t)m/s, where t is in seconds. Determine the magnitude of the boat's velocity when it has traveled 40m. Determine the magnitude of the boat's acceleration ..
Magnitude of the charge on the ballon : An inflated rubber ballon is rubbed with a wool cloth until an excess of a billion electrons is on the ballon. What is the magnitude of the charge on the ballon?
Determine the force that will produce an elastic reduction : A cylindrical bar of aluminum 19 mm (0.75 in) in diameter is to be deformed elastically by application of a force along the bar axis. Using E=10 psi (Modulus of Elasticity), determine the force that will produce an elastic reduction of 1e-4 in. in..
Describe how supervisor should state minimum job requirement : Explain how the supervisor might communicate to his or her department (of all male employees) when a female is about to become part of the work team.
Determine the minimum required wire diameter : a large tower is to be supported by a series of steel wires.it is estimated that the load on each wire will be 11100N. determine the minimum required wire diameter assuming a factor of safety of 2 and a yield strength of 1030MPa.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd