User Account

All Pages

Determine the amplitude of motion of the machine

Assignment Help Mechanical Engineering
Reference no: EM131144002

Consider a machine of mass 70 kg mounted to ground through an isolation system of total stiffness 30,000 N/m, with a measured damping ratio of 0.2.

The machine produces a harmonic force of 450 N at 13 rad/s during steady-state operating conditions.

Determine (a) the amplitude of motion of the machine, (b) the phase shift of the motion (with respect to a zero phase exciting force), (c) the transmissibility ratio, (d) the maximum dynamic force transmitted to the floor, and (e) the maximum velocity of the machine.

Reference no: EM131144002

Questions Cloud

How a therapist can be a solution-focused therapist : Analyze how a therapist can be a solution-focused therapist and, at the same time, provide a complete assessment/diagnosis for chart records. How do you resolve this dilemma?
Discuss the theoretical stance that clients are the experts : Discuss the theoretical stance that clients are the experts on their own situations and that they know what is needed in therapy. What are the attitudes that the therapist must exhibit for this theoretical approach to work?
What are their particular approaches to secularism : Write an essay comparing the secular states of France, United Kingdom, and Israel. What makes each of these states "secular" according to Bowen? What are their particular approaches to secularism?
Design a support system for the machine : Design a support system for the machine (i.e., choose c, k) so that only 10% of the force applied to the machine is transmitted to the base supporting the machine.
Determine the amplitude of motion of the machine : Determine the amplitude of motion of the machine, the phase shift of the motion (with respect to a zero phase exciting force), the transmissibility ratio.
Examine possible occupational stressors : Examine the role of job satisfaction and its influence on retention at the casino. Provide recommendations for improving job satisfaction of the employees and how that can play a part in successfully improving retention.
Determine the maximum absolute value of the bending moment : Draw the shear and bending-moment diagrams for the beam and loading shown, and determine the maximum absolute value
Describe the functionality of the new technology selected : Describe the functionality of the new technology selected for implementation and the challenges associated with the current cybersecurity policy.
Prepare the adjusting entries : The trial balances before and after adjustment for Frinzi Company at the end of its fiscal year are presented.- Prepare the adjusting entries that were made.

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Evaluate the design of the compression

Evaluate the design of the compression spring in order to manufacture the component using the Laser Melting process giving particular consideration to how the process could be used to enhance the functionality of the component.

  The liquid condensate is removed from the system at 60o f

atmospheric air at 90o f and 60 relative humidity flows over a cooling coil at an inlet volumetric flow rate of 2000

  What is the inlet velocity and the exit temperature

Water at 350 psia and 800oF enters a nozzle whose inlet are is 0.4 ft2. The flow rate of steam is 20 lbm/s. Steam leaves at 150 psia and at 825 ft/s. Heat losses from the nozzle per is 3.2 BTU/lbm. What is the inlet velocity and the exit temperature.

  If a case of light bulbs contains 1200 bulbs and the

if a case of light bulbs contains 1200 bulbs and the probability that any one bulb is defective is 0.015 estimate the

  Determine the rate of steam flow-back-pressure steam

A 20 MW back-pressure steam turbine receives steam at stagnation pressure of 4 MPa and stagnation temperature of 300oC, exhausting from the last stage at stagnation pressure of 0.35 MPa. The turbine isentropic efficiency is 0.884, and mechanical loss..

  A rigid tank is divided into two equal parts by a partition

a rigid tank is divided into two equal parts by a partition. one part of the tank contains 2.5 kg of compressed liquid

  Explain what the circuit does

1. The input to the circuit of Figure P12.76 is a square wave having a period of 2 s, maximum value of 5 V, and minimum value of 0 V. Assume all flip-flops are initially in the RESET state.

  Your boss asks you to calculate the flow through a

your boss asks you to calculate the flow through a natural-gas pipeline. since it is 26 in. in diameter it is

  Theoretical amount of oxygen required for the fuel mixture

Consider a 100 mol mixture that is 80.0% methane (CH4) and 20.0% ethane (C2H6). To this mixture is added 22.0% excess air. Of the methane present, 91.90% reacts, 90.90% of which forms carbon dioxide (CO2), and the balance forms carbon monoxide (CO). ..

  Calculate the net work done per cycle for each case

Calculate the net work done per cycle for each case and then plot the thermal efficiency against? on the same plot for each the four values of? Explain why there is an optimum?

  Determine the extent of the strain difference that has

how to solve the following1 for integrated circuits al lines are commonly placed on si to act as electrical conductors

  A woman with wieght 637n lies on a bed of nails the bed has

a woman with wieght 637n lies on a bed of nails. the bed has a weight of 735n and a lenght of 1.72m. the bed is held up

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd