Design the helical compression spring for minimum mass

Assignment Help Mechanical Engineering
Reference no: EM13703878

A helical compression spring made from hard drawn wire needs to be designed to fit inside a 50mm cylindrical cavity and there must be enough space inside the coils for a 20mm cylindrical guide rod.

The spring must provide a pre load of 300N and 600N (maximum load) when compressed a further 25mm. The spring will be used in static conditions only and for this preliminary design the Bergstrasser factor can be approximated as 1.

Design the helical compression spring for minimum mass.

1. Identify the design variables, geometric, strength constraints and the cost function which expresses the total mass of the spring.

2. In point form, describe the optimisation procedure.

3. Show the answer graphically and list the optimum diameters and number of coils.

Reference no: EM13703878

Questions Cloud

How many households will that one installation serve : The USEIA reported that in 2011, the average American household consumed 11,280 kWh for the year. On the outskirts of a small city, an energy company has constructed a single, large wind turbine (blade diameter 30 m). A typical average wind speed ove..
Determine the efficiency of a single fin : A radiator wall measuring 2 m by 3 m (WxH) is held a temperature of 125 °C. Straight aluminium fins (k = 175 W/mK) are to be mounted on the wall. The fins are 5 cm in length and 0.8 mm thick. The system is allowed to convectively transfer heat to amb..
Direction of velocity and acceleration of the rocket : A rocket is launched horizontally (x direction) at an initial velocity of 100 m/s and travels along a parabolic path given by y 2 = (100x) km. If the x component of acceleration is ax = (2t + 15) m/s2 , where t is in seconds, determine magnitude and ..
Scientists have engineered a new hydrocarbon fuel : Scientists have engineered a new hydrocarbon fuel that generates 4100 Btu from every fluid ounce that is burned. At room temperature, this fuel has a density of 214 lbm/ft^3. What is the heating value of this fuel in kJ/kg?
Design the helical compression spring for minimum mass : A helical compression spring made from hard drawn wire needs to be designed to fit inside a 50mm cylindrical cavity and there must be enough space inside the coils for a 20mm cylindrical guide rod.
Water temp in the inlet heavy any effect on required flow : A water pump increases water pressure from 10 psia to 50 psi. Determine the power input required in hp to pump 1.2 ft^3/s of water. Does water temp in the inlet heavy any effect on the required flow?
Estimate the heat flow per unit of area : A composite wall consists of a 1 mm-thick stainless steel plate (AISI 316), 2 cm of plywood, and 2 cm of low-density particle board. The stainless steel surface is maintained at 380 K while the other side loses heat to ambient air at 300 K, with conv..
Two series of cash flows described below equivalent : What value of G makes the two series of cash flows described below equivalent at an interest rate of 3% per year, compounded every 3 months? 22 annual deposits in the amount of $400. 11 annual deposits in the amount of $400 in the first year, and inc..
Heat transfer coefficient at the surface of the base plate : Consider a 1000-W iron whose base plate is made of .5 cm thick aluminium alloy 2024-T6 (p = 2270 kg/m^3, cp= 875 J/kg*K, alpha = 7.3 x 10 ^-5 m^2/s). The base plate has a surface area of .03 m^2.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd